參數資料
型號： AD7711AARZ
廠商： Analog Devices Inc
文件頁數： 17/28頁
文件大?。?/td> 0K
描述： IC ADC 24BIT RTD I SOURCE 24SOIC
標準包裝： 1
位數： 24
采樣率（每秒）： 1.03k
數據接口： 串行
轉換器數目： 1
功率耗散（最大）： 52.5mW
電壓電源： 模擬和數字，雙 ±
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 24-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 24-SOIC W
包裝： 管件
輸入數目和類型： 2 個差分，單極；2 個差分，雙極
REV. D
AD7711A
–24–
SIMPLIFYING THE EXTERNAL CLOCKING MODE
INTERFACE
In many applications, the user may not require the facility of
writing to the on-chip calibration registers. In this case, the
serial interface to the AD7711A in external clocking mode can
be simplified by connecting the
TFS line to the A0 input of the
AD7711A (see Figure 14). This means that any write to the
device will load data to the control register (since A0 is low
while
TFS is low), and any read to the device will access data
from the output data register or from the calibration registers
(since A0 is high while
RFS is low). It should be noted that in
this arrangement, the user does not have the capability of read-
ing from the control register.
AD7711A
RFS
SDATA
SCLK
TFS
A0
FOUR
INTERFACE
LINES
Figure 14. Simplified Interface with
TFS Connected to A0
Another method of simplifying the interface is to generate the
TFS signal from an inverted RFS signal. However, generating
the signals the opposite way around (
RFS from an inverted
TFS) will cause writing errors.
MICROCOMPUTER/MICROPROCESSOR INTERFACING
The AD7711A’s flexible serial interface allows easy interface to
most microcomputers and microprocessors. Figure 15 shows a
flowchart diagram for a typical programming sequence for read-
ing data from the AD7711A to a microcomputer while Figure 16
shows a flowchart diagram for writing data to the AD7711A.
Figures 17, 18, and 19 show some typical interface circuits.
The flowchart of Figure 15 is for continuous read operations
from the AD7711A output register. In the example shown, the
DRDY line is continuously polled. Depending on the micropro-
cessor configuration, the
DRDY line may come to an interrupt
input, in which case the
DRDY will automatically generate an
interrupt without being polled. Reading the serial buffer could
be anything from one read operation up to three read operations
(where 24 bits of data are read into an 8-bit serial register). A
read operation to the control/calibration registers is similar, but,
in this case, the status of
DRDY can be ignored. The A0 line is
brought low when the
RFS line is brought low when reading
from the control register.
The flowchart also shows the bits being reversed after they have
been read in from the serial port. This depends on whether the
microprocessor expects the MSB of the word first or the LSB of
the word first. The AD7711A outputs the MSB first.
NO
YES
BRING
RFS LOW
3
REVERSE
ORDER OF BITS
BRING
RFS HIGH
POLL
DRDY
CONFIGURE AND
INITIALIZE
C/ P
SERIAL PORT
DRDY
LOW?
BRING
RFS, TFS HIGH
START
READ
SERIAL BUFFER
Figure 15. Flowchart for Continuous Read
Operations to the AD7711A
The flowchart in Figure 16 is for a single 24-bit write operation
to the AD7711A control or calibration registers. This shows
data being transferred from data memory to the accumulator
before being written to the serial buffer. Some microprocessor
systems will allow data to be written directly to the serial buffer
from data memory. Writing data to the serial buffer from the
accumulator will generally consist of either two or three write
operations, depending on the size of the serial buffer.
The flowchart also shows the option of the bits being reversed
before being written to the serial buffer. This depends on
whether the first bit transmitted by the microprocessor is the
MSB or the LSB. The AD7711A expects the MSB as the first
bit in the data stream. In cases where the data is being read or
being written in bytes and the data has to be reversed, the bits
will have to be reversed for every byte.
相關PDF資料
PDF描述
ICL3227EIAZA IC TXRX SGL RS232 3-5.5V 16SSOP
AD7880CRZ IC ADC 12BIT MONO LP 24-SOIC
AD9238BCPZ-65 IC ADC 12BIT DUAL 65MSPS 64LFCSP
AD9238BSTZ-65 IC ADC 12BIT DUAL 65MSPS 64-LQFP
ICL3226ECA IC TXRX RS-232 3-5.5V ESD 16SSOP
相關代理商/技術參數
參數描述
AD7711AN 功能描述:IC ADC 24BIT RTD I SOURCE 24-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
AD7711ANZ 功能描述:IC ADC 24BIT RTD I SOURCE 24-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7711ANZ 制造商:Analog Devices 功能描述:IC ADC 24-BIT SIGMA DELTA
AD7711AQ 功能描述:IC ADC 24BIT RTD I SOURCE 24CDIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD7711AR 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*