- 您現在的位置：買賣IC網 > PDF目錄375238 > AD7710SQ (ANALOG DEVICES INC) Signal Conditioning ADC PDF資料下載
參數資料
| 型號： | AD7710SQ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | Signal Conditioning ADC |
| 中文描述： | 2-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, CDIP24 |
| 封裝： | 0.300 INCH, HERMETIC SEALED, CERDIP-24 |
| 文件頁數： | 24/28頁 |
| 文件大?。?/td> | 220K |
| 代理商： | AD7710SQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁
REV. F
–24–
AD7710
SIMPLIFYING THE EXTERNAL CLOCKING MODE
INTERFACE
In many applications, the user may not require the facility of
writing to the on-chip calibration registers. In this case, the
serial interface to the AD7710 in external clocking mode can be
simplified by connecting the
TFS
line to the A0 input of the
AD7710 (see Figure 14). This means that any write to the de-
vice will load data to the control register (since A0 is low while
TFS
is low) and any read to the device will access data from the
output data register or from the calibration registers (since A0 is
high while
RFS
is low). It should be noted that in this arrange-
ment the user does not have the capability of reading from the
control register.
AD7710
SDATA
SCLK
TFS
A0
FOUR
INTERFACE
LINES
RFS
Figure 14. Simplified Interface with
TFS
Connected to A0
Another method of simplifying the interface is to generate the
TFS
signal from an inverted
RFS
signal. However, generating
the signals the opposite way around (
RFS
from an inverted
TFS
) will cause writing errors.
MICROCOMPUTER/MICROPROCESSOR INTERFACING
The AD7710’s flexible serial interface allows for easy interface
to most microcomputers and microprocessors. Figure 15 shows
a flowchart diagram for a typical programming sequence for
reading data from the AD7710 to a microcomputer while Figure
16 shows a flowchart diagram for writing data to the AD7710.
Figures 17, 18 and 19 show some typical interface circuits.
The flowchart of Figure 15 is for continuous read operations
from the AD7710 output register. In the example shown, the
DRDY
line is continuously polled. Depending on the micro-
processor configuration, the
DRDY
line may come to an inter-
rupt input in which case the
DRDY
will automatically generate
an interrupt without being polled. The reading of the serial
buffer could be anything from one read operation up to three
read operations (where 24 bits of data are read into an 8-bit
serial register). A read operation to the control/calibration regis-
ters is similar but in this case the status of
DRDY
can be
ignored. The A0 line is brought low when the
RFS
line is
brought low when reading from the control register.
The flowchart also shows the bits being reversed after they have
been read in from the serial port. This depends on whether the
microprocessor expects the MSB of the word first or the LSB of
the word first. The AD7710 outputs the MSB first.
The flowchart for Figure 16 is for a single 24-bit write operation
to the AD7710 control or calibration registers. This shows data
being transferred from data memory to the accumulator before
being written to the serial buffer. Some microprocessor systems
will allow data to be written directly to the serial buffer from
data memory. The writing of data to the serial buffer from the
accumulator will generally consist of either two or three write
operations, depending on the size of the serial buffer.
NO
YES
BRING
RFS LOW
x3
REVERSE
ORDER OF BITS
BRING
RFS HIGH
POLL DRDY
CONFIGURE &
INITIALIZE
m
C/
m
P
SERIAL PORT
DRDY
LOW
BRING
RFS, TFS HIGH
START
READ
SERIAL BUFFER
Figure 15. Flowchart for Continuous Read Operations to
the AD7710
The flowchart also shows the option of the bits being reversed
before being written to the serial buffer. This depends on
whether the first bit transmitted by the microprocessor is the
MSB or the LSB. The AD7710 expects the MSB as the first bit
in the data stream. In cases where the data is being read or
being written in bytes and the data has to be reversed, the bits
will have to be reversed for every byte.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7710* | Signal Conditioning ADC |
| AD7710 | Signal Conditioning ADC(LC2MOS信號調節A/D轉換器) |
| AD7711AAR | LC2MOS Signal Conditioning ADC with RTD Current Source |
| AD7711ASQ | LC2MOS Signal Conditioning ADC with RTD Current Source |
| AD7711A* | LC2MOS Signal Conditioning ADC with RTD Current Source |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7710SQ/883B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 24-Bit |
| AD7711 | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Signal Conditioning ADC with RTD Excitation Currents |
| AD7711A | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Signal Conditioning ADC with RTD Current Source |
發布緊急采購，3分鐘左右您將得到回復。