- 您現在的位置：買賣IC網 > PDF目錄10543 > AD7450BRZ (Analog Devices Inc)IC ADC 12BIT DIFF IN 1MSPS 8SOIC PDF資料下載
參數資料
| 型號： | AD7450BRZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 4/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT DIFF IN 1MSPS 8SOIC |
| 標準包裝： | 98 |
| 位數： | 12 |
| 采樣率（每秒）： | 1M |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 9.25mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，單極 |
| 配用： | EVAL-AD7450CBZ-ND - BOARD EVALUATION FOR AD7450 |
–12–
AD7450
REFERENCE = 1.25V
1.25V p-p
COMMON-MODE (CM)
CMMIN = 0.625V
CMMAX = 4.42V
REFERENCE = 2.5V
2.5V p-p
COMMON-MODE (CM)
CMMIN = 1.25V
CMMAX = 3.75V
VIN–
VIN
VIN–
VIN
Figure 10. Examples of the Analog Inputs to VIN+
and VIN– for Different Values of VREF for VDD = 5 V
Analog Input Structure
Figure 11 shows the equivalent circuit of the analog input struc-
ture of the AD7450. The four diodes provide ESD protection
for the analog inputs. Care must be taken to ensure that the
analog input signals never exceed the supply rails by more than
300 mV. This will cause these diodes to become forward biased
and start conducting into the substrate. These diodes can conduct
up to 10 mA without causing irreversible damage to the part.
The capacitors, C1, in Figure 11 are typically 4 pF and can prima-
rily be attributed to pin capacitance. The resistors are lumped
components made up of the ON resistance of the switches. The
value of these resistors is typically about 100
. The capacitors,
C2, are the ADC’s sampling capacitors and have a capacitance
of 16 pF typically.
For ac applications, removing high-frequency components from
the analog input signal is recommended by the use of an RC
low-pass filter on the relevant analog input pins. In applications
where harmonic distortion and signal-to-noise ratio are critical,
the analog input should be driven from a low impedance source.
Large source impedances will significantly affect the ac perfor-
mance of the ADC. This may necessitate the use of an input
buffer amplifier. The choice of the op amp will be a function of
the particular application.
VDD
C1
D
VIN+
R1
C2
VIN–
R1
C2
VDD
D
C1
Figure 11. Equivalent Analog Input Circuit
Conversion Phase—Switches Open
Track Phase—Switches Closed
When no amplifier is used to drive the analog input, the source
impedance should be limited to values lower than 1 k
. The
maximum source impedance will depend on the amount of
total harmonic distortion (THD) that can be tolerated. The THD
will increase as the source impedance increases and the perfor-
mance will degrade. Figure 12 shows a graph of the THD versus
the analog input signal frequency for different source impedances.
INPUT FREQUENCY – kHz
–74
–70
–72
–76
–78
–82
–80
10
1000
100
THD
–
dBs
TA = 25 C
VDD = 5V
RIN = 1k
VDD = 3V
RIN = 1k
VDD = 3V
RIN = 100
VDD = 5V
RIN = 100
Figure 12. THD vs. Analog Input Frequency for
Various Source Impedances for VDD = 5 V and 3 V
Figure 13 shows a graph of the THD versus the analog input
frequency for VDD of 5 V
± 5% and 3 V ± 10%, while sampling
at 1 MSPS and 833 kSPS with a SCLK of 18 MHz and
15 MHz, respectively. In this case, the source impedance is 10
.
INPUT FREQUENCY – kHz
–95
–70
–60
–65
–75
–80
–90
–85
10
1000
100
THD
–
dBs
TA = 25 C
VDD = 3.3V
VDD = 2.7V
VDD = 4.75V
VDD = 5.25V
Figure 13. THD vs. Analog Input Frequency for 3 V
± 10% and 5 V ± 5% Supply Voltages
DRIVING DIFFERENTIAL INPUTS
Differential operation requires that VIN+ and VIN– be simulta-
neously driven with two equal signals that are 180
o out of phase.
The common mode must be set up externally and has a range
that is determined by VREF, the power supply, and the particular
amplifier used to drive the analog inputs (see Figures 8 and 9).
Differential modes of operation with either an ac or dc input
provide the best THD performance over a wide frequency range.
Since not all applications have a signal preconditioned for
differential operation, there is often a need to perform single-
ended-to-differential conversion.
Rev. A
相關PDF資料 |
PDF描述 |
|---|---|
| MS3102A24-20P | CONN RCPT 11POS BOX MNT W/PINS |
| AD7475BRZ | IC ADC 12BIT SERIAL LP 8SOIC |
| VI-B50-IV-F2 | CONVERTER MOD DC/DC 5V 150W |
| VE-J4P-MW-F3 | CONVERTER MOD DC/DC 13.8V 100W |
| MS3102A18-12S | CONN RCPT 6POS BOX MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7451 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Pseudo Differential, 1MSPS, 12- & 10-Bit ADCs in 8-lead SOT-23 |
| AD7451ARM | 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 12-bit Serial 8-Pin MSOP 制造商:Rochester Electronics LLC 功能描述:12BIT PSDO DIFF I/PUT,1MSPS SAR ADC I.C. - Bulk 制造商:Analog Devices 功能描述:12BIT SAR ADC DIFF I/P SMD 7451 |
| AD7451ARM-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 12-bit Serial 8-Pin MSOP T/R |
| AD7451ARMZ | 功能描述:IC ADC 12BIT DIFF 1MSPS 8MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7451ART-R2 | 功能描述:IC ADC 12BIT W/DIFF INP SOT-23-8 RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
發(fā)布緊急采購，3分鐘左右您將得到回復。