- 您現在的位置：買賣IC網 > PDF目錄10292 > AD7193BRUZ-REEL (Analog Devices Inc)IC ADC 24BIT SPI 4.8KHZ 28TSSOP PDF資料下載
參數資料
| 型號： | AD7193BRUZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 28/57頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT SPI 4.8KHZ 28TSSOP |
| 標準包裝： | 2,500 |
| 位數： | 24 |
| 采樣率（每秒）： | 4.8k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 4 個差分，單極；4 個差分，雙極；8 個偽差分，單極；8 個偽差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
Data Sheet
AD7193
Rev. D | Page 33 of 56
REFERENCE DETECT
The AD7193 includes on-chip circuitry to detect whether the
part has a valid reference for conversions or calibrations. This
feature is enabled when the REFDET bit in the configuration
register is set to 1. If the voltage between the selected REFINx(+)
and REFINx() pins is less than 0.3 V, the AD7193 detects that
it no longer has a valid reference. In this case, the NOREF bit
of the status register is set to 1. When the voltage between the
selected REFINx(+) and REFINx() pins is greater than 0.6 V,
the AD7193 detects a valid reference so the NOREF bit is set
to 0. The operation of the NOREF bit is undefined when the
voltage between the selected REFINx(+) and REFINx() pins
is between 0.3 V and 0.6 V.
If the AD7193 is performing normal conversions and the NOREF
bit becomes active, the conversion result is all 1s. Therefore, it is
not necessary to continuously monitor the status of the NOREF
bit when performing conversions. It is only necessary to verify
its status if the conversion result read from the ADC data register
is all 1s.
If the AD7193 is performing either an offset or full-scale calibration
and the NOREF bit becomes active, the updating of the respective
calibration registers is inhibited to avoid loading incorrect
coefficients to these registers, and the ERR bit in the status
register is set. If the user is concerned about verifying that a
valid reference is in place every time a calibration is performed,
the status of the ERR bit should be checked at the end of the
calibration cycle.
BIPOLAR/UNIPOLAR CONFIGURATION
The analog input to the AD7193 can accept either unipolar or
bipolar input voltage ranges. A bipolar input range does not
imply that the part can tolerate negative voltages with respect
to system AGND. In pseudo differential mode, signals are
referenced to AINCOM, whereas in differential mode, signals
are referenced to the negative input of the differential pair. For
example, if AINCOM is 2.5 V and the AD7193 AIN1 analog
input is configured for unipolar mode with a gain of 2, the input
voltage range on the AIN1 pin is 2.5 V to 3.75 V when a 2.5 V
reference is used.
If AINCOM is 2.5 V and the AD7193 AIN1 analog input is
configured for bipolar mode with a gain of 2, the analog input
range on AIN1 is 1.25 V to 3.75 V. The bipolar/unipolar option
is chosen by programming the U/B bit in the configuration
register.
DATA OUTPUT CODING
When the ADC is configured for unipolar operation, the output
code is natural (straight) binary with a zero differential input
voltage resulting in a code of 000…000, a midscale voltage resulting
in a code of 100…000, and a full-scale input voltage resulting in
a code of 111…111. The output code for any analog input voltage
can be represented as
Code = (2N × AIN × Gain)/VREF
When the ADC is configured for bipolar operation, the output
code is offset binary with a negative full-scale voltage resulting
in a code of 000…000, a zero differential input voltage resulting
in a code of 100…000, and a positive full-scale input voltage
resulting in a code of 111…111. The output code for any analog
input voltage can be represented as
Code = 2N–1 × [(AIN × Gain/VREF) + 1]
where:
AIN is the analog input voltage.
Gain is the PGA setting (1 to 128).
N = 24.
BURNOUT CURRENTS
The AD7193 contains two 500 nA constant current generators,
one sourcing current from AVDD to AIN(+) and one sinking
current from AIN() to AGND. The currents are switched to
the selected analog input pair. Both currents are either on or off,
depending on the burnout current enable (burn) bit in the
configuration register.
These currents can be used to verify that an external transducer
remains operational before attempting to take measurements on
that channel. After the burnout currents are turned on, they
flow in the external transducer circuit, and a measurement of
the input voltage on the analog input channel can be taken. It
takes some time for the burnout currents to detect an open
circuit condition because the currents must charge any external
capacitors.
There are several reasons that a fault condition is detected: the
front-end sensor may be either open circuit or overloaded, or
the reference may be absent and the NOREF bit in the status
register is set, thus clamping the data to all 1s. The user must
check these three cases before making a determination.
If the voltage measured is 0 V, it may indicate that the transducer
has short circuited. The current sources work over the normal
absolute input voltage range specifications when the analog
inputs are buffered and chop is disabled.
CHANNEL SEQUENCER
The AD7193 includes a channel sequencer, which simplifies
communications with the device in multichannel applications.
The sequencer also optimizes the channel throughput of the
device because the sequencer switches channels at the optimum
rate rather than waiting for instructions via the SPI interface.
Bit CH0 to Bit CH7 in the configuration register are used to enable
the required analog input channels. The analog inputs must be
configured for differential mode or pseudo differential mode
using the pseudo bit in the configuration register. The tempera-
ture sensor is enabled using the TEMP bit in the configuration.
An internal short can also be selected using the short bit in the
configuration register.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27656E17B8PA | CONN RCPT 8POS WALL MNT W/PINS |
| LTC1852CFW#TRPBF | IC A/D CONV 8CH 10BIT 48-TSSOP |
| VE-20J-MX-S | CONVERTER MOD DC/DC 36V 75W |
| LTC1850CFW#TR | IC ADC 10BIT 1.25MSPS 48-TSSOP |
| MS3100C32-7P | CONN RCPT 35POS WALL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7194 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, 4.8 kHz, Ultralow Noise, 24-Bit Sigma-Delta ADC with PGA |
| AD7194BCPZ | 功能描述:IC ADC 24BIT SPI 4.8K 32-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7194BCPZ-REEL | 功能描述:IC ADC 24BIT SPI 4.8KHZ 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7194BCPZ-REEL7 | 功能描述:IC ADC 24BIT SPI 4.8KHZ 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7195 | 制造商:AD 制造商全稱:Analog Devices 功能描述:4.8 kHz, Ultralow Noise, 24-Bit Sigma-Delta ADC with PGA and AC Excitation |
發布緊急采購，3分鐘左右您將得到回復。