參數資料
型號： AD5744
廠商： Analog Devices, Inc.
英文描述： Complete, Quad, 14/16-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC
中文描述： 完整，四路，14/16-Bit，高精度，串行輸入，雙極性電壓輸出DAC
文件頁數： 11/27頁
文件大?。?/td> 243K
代理商： AD5744
Preliminary Technical Data
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Rev. PrA 15-Nov-04| Page 11 of 27
AD5744/64
TOP VIEW
(Not to Scale)
SYNC
SCLK
SDIN
SDO
CLR
LDAC
D1
D0
AGNDA
VOUTA
VOUTB
AGNDB
AGNDC
VOUTC
VOUTD
AGNDD
R
R
D
D
C
A
D
P
I
A
S
B
A
D
A
S
T
R
R
R
R
1
32
25
9
16
8
24
17
PIN 1
INDICATOR
Figure 6. 32-Lead TQFP Pin Configuration Diagram
Table 5. Pin Function Descriptions
Pin No.
1
Mnemonic
SYNC
Function
Active Low Input. This is the frame synchronization signal for the serial interface.
While SYNC is low, data is transferred in on the falling edge of SCLK.
Serial Clock Input. Data is clocked into the shift register on the falling edge of SCLK.
This operates at clock speeds up to 30 MHz.
Serial Data Input. Data must be valid on the falling edge of SCLK.
Serial Data Output. Used to clock data from the serial register in daisy-chain or
readback mode.
Active Low Input. Asserting this pin sets the DAC registers to 0x0000.
Load DAC. Logic input. This is used to update the DAC registers and consequently
the analog output. When tied permanently low, the addressed DAC register is
updated on the 24
th
clock of the serial register write. If LDAC is held high during the
write cycle, the DAC input register is updated but the output is held off until the
falling edge of LDAC. In this mode, all analog outputs can be updated
simultaneously on the falling edge of LDAC.
D0 and D1 form a digital I/O port. The user can configure these pins as inputs or
outputs that are configurable and readable over the serial interface. When
configured as inputs, these pins have weak internal pull-ups to DV
CC
.
Reset Logic Output. This is the output from the on-chip voltage monitor used in the
reset circuit. If desired, it may be used to control other system components.
Reset Logic Input. This input allows external access to the internal reset logic.
Applying a Logic 0 to this input resets the DAC output to 0 V. In normal operation,
RSTIN should be tied to Logic 1.
Digital GND Pin.
Digital Supply Pin. Voltage ranges from 2.7 V to 5.5 V. When programmed as
outputs, D0 and D1 are referenced to DV
CC
.
Positive Analog Supply Pins. Voltage ranges from 11.4 V to 16.5 V.
Ground Reference Point for Analog Circuitry.
Negative Analog Supply Pins. Voltage ranges from –11.4 V to –16.5 V.
2
SCLK
13
3
4
SDIN
13
SDO
5
6
CLR
13
LDAC
7, 8
D0, D1
9
RSTOUT
10
RSTIN
11
12
DGND
DV
CC
13, 31
14
15, 30
AV
DD
PGND
AV
SS
13
Internal pull-up device on this logic input. Therefore, it can be left floating and will default to a logic high condition.
相關PDF資料
PDF描述
AD5744ASU Complete, Quad, 14/16-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC
AD5744BSU Complete, Quad, 14/16-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC
AD5744CSU Complete, Quad, 14/16-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC
AD5754R Quad 12-Bit Serial Input Unipolar/Bipolar Voltage Output DAC
AD5725 Quad 12-Bit Serial Input Unipolar/Bipolar Voltage Output DAC
相關代理商/技術參數
參數描述
AD5744ASU 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete, Quad, 14/16-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC
AD5744BSU 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete, Quad, 14/16-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC
AD5744CSU 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete, Quad, 14/16-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC
AD5744R 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete Quad, 14-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC
AD5744R_08 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete Quad, 14-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*