參數資料
型號: A42MX16-2CQ100B
廠商: Electronic Theatre Controls, Inc.
英文描述: 40MX and 42MX FPGA Families
中文描述: 40MX和42MX FPGA系列
文件頁數: 39/120頁
文件大小: 854K
代理商: A42MX16-2CQ100B
25
4958B–AUTO–11/10
Atmel ATA6285/ATA6286 [Preliminary]
Bit 1 - EEWE: EEPROM Write Enable
The EEPROM Write Enable Signal EEWE is the write strobe to the EEPROM. When address
and data are correctly set up, the EEWE bit must be written to one to write the value into the
EEPROM. The EEMWE bit must be written to one before a logical one is written to EEWE; oth-
erwise no EEPROM write takes place. The following procedure should be followed when writing
the EEPROM (the order of steps 3 and 4 is not essential):
Wait until EEWE becomes zero.
Wait until SELFPRGEN in SPMCSR register becomes zero.
Write new EEPROM address to EEAR register (optional).
Write new EEPROM data to EEDR register (optional).
Write a logical one to the EEMWE bit while writing a zero to EEWE bit in EECR register.
Within four clock cycles after setting EEMWE, write a logical one to EEWE.
The EEPROM cannot be programmed during a CPU write to the Flash memory. The software
must check that the Flash programming is completed before initiating a new EEPROM write.
Step 2 is only relevant if the software contains a Boot Loader allowing the CPU to program the
Flash. If the Flash is never being updated by the CPU, step 2 can be omitted. See Section 3.19
programming.
Caution: An interrupt between step 5 and step 6 will make the write cycle fail, since the
EEPROM Master Write Enable will time-out. If an interrupt routine accessing the EEPROM is
interrupting another EEPROM access, the EEAR or EEDR Register will be modified, causing the
interrupted EEPROM access to fail. It is recommended to have the Global Interrupt Flag cleared
during all the steps to avoid these problems.
When the write access time has elapsed, the EEWE bit is cleared by hardware. The user soft-
ware can poll this bit and wait for a zero before writing the next byte. When EEWE has been set,
the CPU is halted for two cycles before the next instruction is executed.
Bit 0 - EERE: EEPROM Read Enable
The EEPROM Read Enable Signal EERE is the read strobe to the EEPROM. When the correct
address is set up in the EEAR Register, the EERE bit must be written to a logic one to trigger the
EEPROM read. The EEPROM read access takes one instruction, and the requested data is
available immediately. When the EEPROM is read, the CPU is halted for four cycles before the
next instruction is executed. The user should poll the EEWE bit before starting the read opera-
tion. If a write operation is in progress, it is neither possible to read the EEPROM, nor to change
the EEAR Register.
相關PDF資料
PDF描述
A42MX24-2CQ100B 40MX and 42MX FPGA Families
A42MX36-2CQ100B 40MX and 42MX FPGA Families
A42MX02-2CQ100ES 40MX and 42MX FPGA Families
A42MX04-2CQ100ES Sensor Cable Assembly; Connector Type A:M12 Plug; Connector Type B:Stripped End Leads; Cable Length:2m; No. of Contacts:5; No. of Positions:5 RoHS Compliant: Yes
A42MX09-2CQ100ES Sensor Cable Assembly; Connector Type A:M12 Plug; Connector Type B:M12 Receptacle; Cable Length:2m; No. of Contacts:5; No. of Positions:5 RoHS Compliant: Yes
相關代理商/技術參數
參數描述
A42MX16-2CQ100ES 制造商:未知廠家 制造商全稱:未知廠家 功能描述:40MX and 42MX FPGA Families
A42MX16-2CQ100I 制造商:未知廠家 制造商全稱:未知廠家 功能描述:40MX and 42MX FPGA Families
A42MX16-2CQ100M 制造商:未知廠家 制造商全稱:未知廠家 功能描述:40MX and 42MX FPGA Families
A42MX16-2PL100 制造商:未知廠家 制造商全稱:未知廠家 功能描述:40MX and 42MX FPGA Families
A42MX16-2PL100A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:40MX and 42MX FPGA Families