- 您現在的位置：買賣IC網 > PDF目錄122717 > 935271490512 (NXP SEMICONDUCTORS) 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68 PDF資料下載
參數資料
| 型號： | 935271490512 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68 |
| 封裝： | PLASTIC, MS-018, SOT-188-2, LCC-68 |
| 文件頁數： | 20/56頁 |
| 文件大?。?/td> | 715K |
| 代理商： | 935271490512 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
Philips Semiconductors
SC16C554/554D
Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder
Product data
Rev. 02 — 13 March 2003
27 of 53
9397 750 11002
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
7.5 Line Control Register (LCR)
The Line Control Register is used to specify the asynchronous data communication
format. The word length, the number of stop bits, and the parity are selected by
writing the appropriate bits in this register.
Table 14:
Line Control Register bits description
Bit
Symbol
Description
7
LCR[7]
Divisor latch enable. The internal baud rate counter latch and
Enhance Feature mode enable.
Logic 0 = Divisor latch disabled (normal default condition).
Logic 1 = Divisor latch and enhanced feature register enabled.
6
LCR[6]
Set break. When enabled, the Break control bit causes a break
condition to be transmitted (the TX output is forced to a logic 0
state). This condition exists until disabled by setting LCR[6] to a
logic 0.
Logic 0 = no TX break condition (normal default condition).
Logic 1 = forces the transmitter output (TX) to a logic 0 for
alerting the remote receiver to a line break condition.
5
LCR[5]
Set parity. If the parity bit is enabled, LCR[5] selects the forced
parity format. Programs the parity conditions (see Table 15).
Logic 0 = parity is not forced (normal default condition).
LCR[5] = logic 1 and LCR[4] = logic 0: parity bit is forced to a
logical 1 for the transmit and receive data.
LCR[5] = logic 1 and LCR[4] = logic 1: parity bit is forced to a
logical 0 for the transmit and receive data.
4
LCR[4]
Even parity. If the parity bit is enabled with LCR[3] set to a logic 1,
LCR[4] selects the even or odd parity format.
Logic 0 = ODD Parity is generated by forcing an odd number of
logic 1s in the transmitted data. The receiver must be
programmed to check the same format (normal default
condition).
Logic 1 = EVEN Parity is generated by forcing an even number
of logic 1s in the transmitted data. The receiver must be
programmed to check the same format.
3
LCR[3]
Parity enable. Parity or no parity can be selected via this bit.
Logic 0 = no parity (normal default condition).
Logic 1 = a parity bit is generated during the transmission,
receiver checks the data and parity for transmission errors.
2
LCR[2]
Stop bits. The length of stop bit is specied by this bit in
conjunction with the programmed word length (see Table 16).
Logic 0 or cleared = default condition.
1-0
LCR[1-0]
Word length bits 1, 0. These two bits specify the word length to be
transmitted or received (see Table 17).
Logic 0 or cleared = default condition.
相關PDF資料 |
PDF描述 |
|---|---|
| 935271979118 | 8 I/O, PIA-GENERAL PURPOSE, PQCC16 |
| 935263358512 | 8-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PDSO20 |
| 9UMS9633BKLFT | 166.67 MHz, OTHER CLOCK GENERATOR, PQCC48 |
| 935263686518 | 6 CHANNEL(S), 200M bps, SERIAL COMM CONTROLLER, PQFP64 |
| 9154A-04CS16 | 100 MHz, OTHER CLOCK GENERATOR, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935271933518 | 制造商:NXP Semiconductors 功能描述:IC D-TYPE POS TRG DUAL 56VFBGA |
| 935271933551 | 制造商:NXP Semiconductors 功能描述:IC D-TYPE POS TRG DUAL 56VFBGA |
| 935271933557 | 制造商:NXP Semiconductors 功能描述:IC D-TYPE POS TRG DUAL 56VFBGA |
| 935271937518 | 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA |
| 935271937551 | 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA |
發布緊急采購，3分鐘左右您將得到回復。