- 您現在的位置：買賣IC網 > PDF目錄294733 > 91C94 (SMSC Corporation) ISA/PCMCIA SINGLE CHIP ETHERNET CONTROLLER WITH RAM PDF資料下載
參數資料
| 型號： | 91C94 |
| 廠商： | SMSC Corporation |
| 英文描述： | ISA/PCMCIA SINGLE CHIP ETHERNET CONTROLLER WITH RAM |
| 中文描述： | 的ISA / PCMCIA的單芯片以太網控制器與RAM |
| 文件頁數： | 94/120頁 |
| 文件大?。?/td> | 447K |
| 代理商： | 91C94 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁當前第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
75
AUTO
RELEASE
-
When
set,
successful
transmit packets are not written into completion
FIFO,
and
their
memory
is
released
automatically.
1)
One interrupt per packet: enable TX INT,
set AUTO RELEASE=0.
The software driver
can find the completion result in memory and
process the interrupt one packet at a time.
Depending on the completion code the driver
will take different actions. Note that the transmit
process
is
working
in
parallel
and
other
transmissions might be taking place.
The
LAN91C94
is
virtually
queuing
the
packet
numbers and their status words.
In this case, the transmit interrupt service
routine can find the next packet number to be
serviced by reading the TX DONE PACKET
NUMBER at the FIFO PORTS register.
This
eliminates the need for the driver to keep a list
of packet numbers being transmitted.
The
numbers are queued by the LAN91C94 and
provided back to the CPU as their transmission
completes.
2)
One interrupt per sequence of packets:
Enable TX EMPTY INT and TX INT, set AUTO
RELEASE=1. TX EMPTY INT is generated only
after transmitting the last packet in the FIFO.
TX INT will be set on a fatal transmit error
allowing the CPU to know that the transmit
process has stopped and therefore the FIFO will
not be emptied.
This mode has the advantage of a smaller CPU
overhead, and faster memory de-allocation.
Note that when AUTO RELEASE=1 the CPU is
not provided with the packet numbers that
completed successfully.
Note: The pointer register is shared by any
process accessing the LAN91C94 memory. In
order to allow processes to be interruptable,
the
interrupting
process
is
responsible
for
reading the pointer value before modifying it,
saving it, and restoring it before returning from
the interrupt.
Typically there would be three processes using
the pointer:
1)
Transmit
loading
(sometimes
interrupt
driven)
2)
Receive unloading (interrupt driven)
3)
Transmit Status reading (interrupt driven).
1) and 3) also share the usage of the Packet
Number
Register.
Therefore
saving
and
restoring the PNR is also required from interrupt
service routines.
POWER DOWN
The LAN91C94 can enter power down mode by
means of the PWRDWN pin (pin 68) or the
PWRDN bit (Control Register, bit 13).
The
power down current is 8 mA.
When in power
down mode, the LAN91C94 will:
- Stop the crystal oscillator
- Tristate:
Data Bus
Interrupts
nIOCS16
10BASE-T and AUI outputs
Turn off analog bias currents
- Drive the EEPROM and ROM outputs inactive
- Preserve contents of registers and memory
The PWRDWN pin is internally gated with the
RESET (RESET pin before de-glitching) and
with the SRESET bit (COR bit 7). This gating
function
internally
negates
power
down
whenever RESET is high or SRESET is high to
allow the oscillator to run during RESET. Except
for this gating function, all other uses of the
RESET pin use a de-glitched version of the
signal as defined in the pin description section.
相關PDF資料 |
PDF描述 |
|---|---|
| 92_TNC-50-0-4/111_NE | BOARD TERMINATED, FEMALE, TNC CONNECTOR, SURFACE MOUNT, JACK |
| 92_TNC-50-0-4/111_NM | BOARD TERMINATED, FEMALE, TNC CONNECTOR, SURFACE MOUNT, JACK |
| 92082-314 | 14 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
| 92082-316 | 16 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
| 92082-318 | 18 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 91CCC3 | 制造商:Wirepro 功能描述:Connector Accessories Cap and Chain For Receptacle |
| 91-CCC3 | 制造商:CDM ELECTRONIC FORMERLY WPI 功能描述:connector accessory,circular microphone,cap and chain for receptacle |
| 91-CCC-3 | 制造商:Amphenol Corporation 功能描述: 制造商:TE Connectivity 功能描述: |
| 91CR10 | 制造商:TT Electronics / BI Technologies 功能描述:Res Cermet Trimmer 10 Ohm 20% 1/2W 1(Elec)/1(Mech)Turn (9.53 X 9.78 X 7.11mm) Pin Thru-Hole Box |
| 91CR100 | 功能描述:微調電阻 - 通孔 3/8inch 100 Thumbwheel RoHS:否 制造商:Vishay/Sfernice 產品:Trimmer Resistors - Multi Turn 產品類型:Multiturn 轉數:14 錐度:Linear 電阻:10 kOhms 電壓額定值:250 V 端接類型:Pin 功率額定值:250 mW (1/4 W) 容差:10 % 溫度系數:100 PPM / C |
發布緊急采購，3分鐘左右您將得到回復。