參數資料
型號： 39VF6401
廠商： Silicon Storage Technology, Inc.
元件分類： FLASH
英文描述： 64 Mbit (x16) Multi-Purpose Flash Plus
中文描述： 64兆位（x16）的多功能閃存+
文件頁數： 3/32頁
文件大小： 513K
代理商： 39VF6401
Preliminary Specifications
16 Mbit / 32 Mbit / 64 Mbit Multi-Purpose Flash Plus
SST39VF1601 / SST39VF3201 / SST39VF6401
SST39VF1602 / SST39VF3202 / SST39VF6402
3
2003 Silicon Storage Technology, Inc.
S71223-03-000
11/03
To resume Sector-Erase or Block-Erase operation which has
been suspended the system must issue Erase Resume
command. The operation is executed by issuing one byte
command sequence with Erase Resume command (30H)
at any address in the last Byte sequence.
Chip-Erase Operation
The SST39VF160x/320x/640x provide a Chip-Erase oper-
ation, which allows the user to erase the entire memory
array to the “1” state. This is useful when the entire device
must be quickly erased.
The Chip-Erase operation is initiated by executing a six-
byte command sequence with Chip-Erase command
(10H) at address 5555H in the last byte sequence. The
Erase operation begins with the rising edge of the sixth
WE# or CE#, whichever occurs first. During the Erase
operation, the only valid read is Toggle Bit or Data# Polling.
See Table 6 for the command sequence, Figure 9 for tim-
ing diagram, and Figure 23 for the flowchart. Any com-
mands issued during the Chip-Erase operation are
ignored. When WP# is low, any attempt to Chip-Erase will
be ignored. During the command sequence, WP# should
be statically held high or low.
Write Operation Status Detection
The SST39VF160x/320x/640x provide two software
means to detect the completion of a Write (Program or
Erase) cycle, in order to optimize the system write cycle
time. The software detection includes two status bits: Data#
Polling (DQ
7
) and Toggle Bit (DQ
6
). The End-of-Write
detection mode is enabled after the rising edge of WE#,
which initiates the internal Program or Erase operation.
The actual completion of the nonvolatile write is asyn-
chronous with the system; therefore, either a Data# Poll-
ing or Toggle Bit read may be simultaneous with the
completion of the write cycle. If this occurs, the system
may possibly get an erroneous result, i.e., valid data may
appear to conflict with either DQ
7
or DQ
6
. In order to pre-
vent spurious rejection, if an erroneous result occurs, the
software routine should include a loop to read the
accessed location an additional two (2) times. If both
reads are valid, then the device has completed the Write
cycle, otherwise the rejection is valid.
Data# Polling (DQ
7
)
When the SST39VF160x/320x/640x are in the internal
Program operation, any attempt to read DQ
7
will produce
the complement of the true data. Once the Program oper-
ation is completed, DQ
7
will produce true data. Note that
even though DQ
7
may have valid data immediately follow-
ing the completion of an internal Write operation, the
remaining data outputs may still be invalid: valid data on the
entire data bus will appear in subsequent successive Read
cycles after an interval of 1 μs. During internal Erase oper-
ation, any attempt to read DQ
7
will produce a ‘0’. Once the
internal Erase operation is completed, DQ
7
will produce a
‘1’. The Data# Polling is valid after the rising edge of fourth
WE# (or CE#) pulse for Program operation. For Sector-,
Block- or Chip-Erase, the Data# Polling is valid after the
rising edge of sixth WE# (or CE#) pulse. See Figure 6 for
Data# Polling timing diagram and Figure 20 for a flowchart.
Toggle Bits (DQ6 and DQ2)
During the internal Program or Erase operation, any con-
secutive attempts to read DQ
6
will produce alternating “1”s
and “0”s, i.e., toggling between 1 and 0. When the internal
Program or Erase operation is completed, the DQ
6
bit will
stop toggling. The device is then ready for the next opera-
tion. For Sector-, Block-, or Chip-Erase, the toggle bit (DQ
6
)
is valid after the rising edge of sixth WE# (or CE#) pulse.
DQ
6
will be set to “1” if a Read operation is attempted on an
Erase-Suspended Sector/Block. If Program operation is ini-
tiated in a sector/block not selected in Erase-Suspend
mode, DQ
6
will toggle.
An additional Toggle Bit is available on DQ
2
, which can be
used in conjunction with DQ
6
to check whether a particular
sector is being actively erased or erase-suspended. Table 1
shows detailed status bits information. The Toggle Bit
(DQ
2
) is valid after the rising edge of the last WE# (or CE#)
pulse of Write operation. See Figure 7 for Toggle Bit timing
diagram and Figure 20 for a flowchart.
Note:
DQ
7
and DQ
2
require a valid address when reading
status information.
TABLE
1: W
RITE
O
PERATION
S
TATUS
Status
Normal
Operation
DQ
7
DQ
7
#
DQ
6
Toggle
DQ
2
Standard
Program
Standard
Erase
Read from
Erase-Suspended
Sector/Block
Read from
Non- Erase-Suspended
Sector/Block
Program
No Toggle
0
Toggle
Toggle
Erase-
Suspend
Mode
1
1
Toggle
Data
Data
Data
DQ
7
#
Toggle
N/A
T1.0 1223
相關PDF資料
PDF描述
3A11 Power Transistor Arrays
3a325 Surface Mount Balun
3ATL6 TASTE KONTAKTELEMENT DURCHSTECK
1B09 LEITERPLATTENTATSTER WIPPE RAHMEN SCHWAR
1B08 LEITERPLATTENTATSTER WIPPE RAHMEN ROT
相關代理商/技術參數
參數描述
39VR-R2-2111 制造商:LIGHTING COMP DESIGN 功能描述: 制造商:Lighting Components & Design Inc 功能描述:
39W BLANK DIALS 制造商:SIFAM 功能描述:SCALE BLANK 39W PK4
39W0-100UA0-100 制造商:SIFAM 功能描述:METER 39W 0-100UA 制造商:SIFAM 功能描述:METER, 39W, 0-100UA
39W0-1MA0-100 制造商:SIFAM 功能描述:METER 39W 0-1MA 制造商:SIFAM 功能描述:METER, 39W, 0-1MA 制造商:SIFAM 功能描述:METER, 39W, 0-1MA; Terminal Resistance Range:50ohm; Meter Function:AC Milliamps / DC Milliamps; Meter Range:0mA to 1mA; Panel Cutout Height:40.5mm; Panel Cutout Width:91.5mm; Scale Length:78mm; SVHC:No SVHC (19-Dec-2012); Accuracy ;RoHS Compliant: Yes
39W0-30MA0-30 制造商:SIFAM 功能描述:METER 39W 0-1MA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*