參數資料
型號： 29LV400C-90
廠商： Macronix International Co., Ltd.
英文描述： 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
中文描述： 4分位[為512k × 8 / 256K × 16] CMOS單電壓3V時僅閃存
文件頁數： 12/68頁
文件大小： 906K
代理商： 29LV400C-90
12
P/N:PM1155
MX29LV400C T/B
REV. 1.5, APR. 24, 2006
Pins
Manufacture code
A0
VIL
VIL
VIH
VIH
VIH
VIH
X
X
A1
VIL
VIL
VIL
VIL
VIL
VIL
VIH
VIH
Q15~Q8 Q7
00H
X
22H
X
22H
X
X
X
Q6
1
1
0
0
0
0
0
0
Q5
0
0
1
1
1
1
0
0
Q4
0
0
1
1
1
1
0
0
Q3
0
0
1
1
1
1
0
0
Q2 Q1
0
0
0
0
0
0
0
0
Q0
0
0
1
1
0
0
1
0
Code(Hex)
00C2H
C2H
22B9H
B9H
22BAH
BAH
01H (Protected)
00H (Unprotected)
Word
Byte
Word
Byte
Word
Byte
1
1
1
1
1
1
0
0
1
1
0
0
1
1
0
0
Device code
for MX29LV400CT
Device code
for MX29LV400CB
Sector Protection
Verification
TABLE 6. EXPANDED SILICON ID CODE
READING ARRAY DATA
The device is automatically set to reading array data
after device power-up. No commands are required to re-
trieve data. The device is also ready to read array data
after completing an Automatic Program or Automatic
Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The sys-
tem can read array data using the standard read tim-
ings, except that if it reads at an address within erase-
suspended sectors, the device outputs status data. Af-
ter completing a programming operation in the Erase
Suspend mode, the system may once again read array
data with the same exception. See "Erase Suspend/Erase
Resume Commands" for more infor-mation on this mode.
The system must issue the reset command to re-en-
able the device for reading array data if Q5 goes high, or
while in the autoselect mode. See the "Reset Command"
section, next.
RESET COMMAND
Writing the reset command to the device resets the de-
vice to reading array data. Address bits are don't care for
this command.
The reset command may be written between the se-
quence cycles in an erase command sequence before
erasing begins. This resets the device to reading array
data. Once erasure begins, however, the device ignores
reset commands until the operation is complete.
The reset command may be written between the se-
quence cycles in a program command sequence be-fore
programming begins. This resets the device to reading
array data (also applies to programming in Erase Sus-
pend mode). Once programming begins, however, the
device ignores reset commands until the operation is
complete.
The reset command may be written between the se-
quence cycles in an SILICON ID READ command se-
quence. Once in the SILICON ID READ mode, the reset
command must be written to return to reading array data
(also applies to SILICON ID READ during Erase Sus-
pend).
If Q5 goes high during a program or erase operation, writ-
ing the reset command returns the device to read-ing
array data (also applies during Erase Suspend).
相關PDF資料
PDF描述
29LV650 64M (4M x 16) BIT
29LV800BB-70 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV800BB-90 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV800BT-70 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV800BT-90 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
相關代理商/技術參數
參數描述
29LV51215JU 制造商: 功能描述: 制造商:undefined 功能描述:
29LV512-15JU 制造商: 功能描述: 制造商:undefined 功能描述:
29LV640 制造商:MCNIX 制造商全稱:Macronix International 功能描述:flash memory
29LV640DL90RZI 制造商: 功能描述: 制造商:undefined 功能描述:
29LV640MU90RPCI 制造商: 功能描述: 制造商:undefined 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*