參數資料
型號： 28F400BV-TB
廠商： Intel Corp.
英文描述： 4-MBIT (256K X 16, 512K X 8)SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY
中文描述： 4兆位（256 × 16，為512k × 8）SmartVoltage啟動塊閃存系列
文件頁數： 18/49頁
文件大小： 427K
代理商： 28F400BV-TB
SMART 3 ADVANCED BOOT BLOCK
–WORD-WIDE
E
18
PRELIMINARY
When the WSM is active, SR.7 will indicate the
status of the WSM; the remaining bits in the status
register indicate whether or not the WSM was
successful in performing the desired operation (see
Table 7).
3.2.3.1
Clearing the Status Register
The WSM sets status bits 1 through 7 to
“1,” and
clears bits 2, 6 and 7
to “0,” but cannot clear status
bits 1 or 3 through 5 to “0.” Because bits 1, 3, 4 and
5 indicate various error conditions, these bits can
only be cleared by the controlling CPU through the
use of the Clear Status Register (50H) command.
By allowing the system software to control the
resetting of these bits, several operations may be
performed (such as cumulatively programming
several addresses or erasing multiple blocks in
sequence) before reading the status register to
determine if an error occurred during that series.
Clear the Status Register before beginning another
command or sequence. Note, again, that the Read
Array command must be issued before data can be
read from the memory array.
3.2.4
PROGRAM MODE
Programming is executed using a two-write
sequence. The Program Setup command (40H) is
written to the CUI followed by a second write which
specifies the address and data to be programmed.
The WSM will execute the following sequence of
internally timed events:
1.
Program the desired bits of the addressed
memory.
Verify that the desired bits are sufficiently
programmed.
2.
Programming of the memory results in specific bits
within an address location being changed to a “0.” If
the user attempts to program “1”s, there will be no
change of the memory cell contents and no error
occurs.
The status register indicates programming status:
while the program sequence is executing, bit 7 of
the status register is a “0.” The status register can
be polled by toggling either CE# or OE#. While
programming, the only valid commands are Read
Status Register, Program Suspend, and Program
Resume.
When programming is complete, the Program
Status bits should be checked. If the programming
operation was unsuccessful, bit SR.4 of the status
register is set to indicate a program failure. If SR.3
is set then V
PP
was not within acceptable limits, and
the WSM did not execute the program command. If
SR.1 is set, a program operation was attempted to
a locked block and the operation was aborted.
The status register should be cleared before
attempting the next operation. Any CUI instruction
can follow after programming is completed;
however, to prevent inadvertent status register
reads, be sure to reset the CUI to read array mode.
3.2.4.1
Suspending and Resuming
Program
The Program Suspend command allows program
suspension in order to read data in other locations
of memory. Once the programming process starts,
writing the Program Suspend command to the CUI
requests that the WSM suspend the program
sequence (at predetermined points in the program
algorithm). The device continues to output status
register data after the Program Suspend command
is written. Polling status register bits SR.7 and SR.2
will determine when the program operation has
been suspended (both will be set to “1”).
t
WHRH1
/t
EHRH1
specify the program suspend latency.
A Read Array command can now be written to the
CUI to read data from blocks other than that which
is suspended. The only other valid commands,
while program is suspended, are Read Status
Register and Program Resume. After the Program
Resume command is written to the flash memory,
the WSM will continue with the program process
and status register bits SR.2 and SR.7 will
automatically be cleared. After the Program
Resume
command
is
automatically outputs status register data when
read (see Figure 8, Program Suspend/Resume
Flowchart). V
must remain at the same V
PP
level
used for program while in program suspend mode.
RP# must also remain at V
IH.
written,
the
device
3.2.4.2
V
Supply Voltage during
Program
V
PP
supply voltage considerations are outlined in
Section 3.4
相關PDF資料
PDF描述
28F400BX-TB 4-MBIT (256K X 16, 512K X 8) BOOT BLOCK FLASH MEMORY FAMILY
28F410-100M1 4M-BIT (512K X 8) CMOS FLASH MEMORY
28F512 512K(64Kx8)CMOS FLASH MEMORY
28F640C3 3 Volt Advanced Boot Block Flash Memory(3 V 高級快速引導塊閃速存儲器)
28F640J3C-120 Intel StrataFlash Memory (J3)
相關代理商/技術參數
參數描述
28F400BX-B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-MBIT (256K X 16. 512K X 8) BOOT BLOCK FLASH MEMORY FAMILY
28F400BX-T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-MBIT (256K X 16. 512K X 8) BOOT BLOCK FLASH MEMORY FAMILY
28F400BX-T/B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
28F400BX-TB 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:4-MBIT (256K X 16, 512K X 8) BOOT BLOCK FLASH MEMORY FAMILY
28F400BX-TL/BL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*