- 您現在的位置：買賣IC網 > PDF目錄371435 > 28F200BX-TB (Intel Corp.) 2-MBIT (128K x 16, 256K x 8) BOOT BLOCK FLASH MEMORY FAMILY PDF資料下載
參數資料
| 型號： | 28F200BX-TB |
| 廠商： | Intel Corp. |
| 英文描述： | 2-MBIT (128K x 16, 256K x 8) BOOT BLOCK FLASH MEMORY FAMILY |
| 中文描述： | 2兆位（128K的× 16，256K × 8）啟動塊閃存系列 |
| 文件頁數： | 18/55頁 |
| 文件大?。?/td> | 636K |
| 代理商： | 28F200BX-TB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
2-MBIT SmartVoltage BOOT BLOCK FAMILY
E
18
SEE NEW DESIGN RECOMMENDATIONS
Table 6. Command Codes and Descriptions
Code
Device Mode
Description
00
Invalid/
Reserved
Unassigned commands that should not be used. Intel reserves the right to redefine
these codes for future functions.
FF
Read Array
Places the device in read array mode, so that array data will be output on the data
pins.
40
Program
Set-Up
Sets the CUI into a state such that the next write will latch the Address and Data
registers on the rising edge and begin the program algorithm. The device then
defaults to the read status mode, where the device outputs status register data
when OE# is enabled. To read the array, issue a Read Array command.
To cancel a program operation after issuing a Program Set-Up command, write all
1’s (FFH for x8, FFFFH for x16)
to the CUI. This will return to read status register
mode after a standard program time without modifying array contents. If a program
operation has already been initiated to the WSM this command cannot cancel that
operation in progress.
10
Alternate
Prog Set-Up
(See 40H/Program Set-Up)
20
Erase
Set-Up
Prepares the CUI for the Erase Confirm command. If the next command is not an
Erase Confirm command, then the CUI will set both the Program Status (SR.4) and
Erase Status (SR.5) bits of the status register to a “1,” place the device into the
read status register state, and wait for another command without modifying array
contents. This can be used to cancel an erase operation after the Erase Set-Up
command has been issued. If an operation has already been initiated to the WSM
this can not cancel that operation in progress.
D0
Erase
Resume/
Erase
Confirm
If the previous command was an Erase Set-Up command, then the CUI will latch
address and data, and begin erasing the block indicated on the address pins.
During erase, the device will respond only to the Read Status Register and Erase
Suspend commands and will output status register data when OE# is toggled low.
Status register data is updated by toggling either OE# or CE# low.
B0
Erase
Suspend
Valid only while an erase operation is in progress and will be ignored in any other
circumstance. Issuing this command will begin to suspend erase operation. The
status register will indicate when the device reaches erase suspend mode. In this
mode, the CUI will respond only to the Read Array, Read Status Register, and
Erase Resume commands and the WSM will also set the WSM Status bit to a “1”
(ready). The WSM will continue to idle in the SUSPEND state, regardless of the
state of all input control pins except RP#, which will immediately shut down the
WSM and the remainder of the chip, if it is made active. During a suspend
operation, the data and address latches will remain closed, but the address pads
are able to drive the address into the read path. See Section 3.3.4.1.
70
Read Status
Register
Puts the device into the read status register mode, so that reading the device
outputs status register data, regardless of the address presented to the device.
The device automatically enters this mode after program or erase has completed.
This is one of the two commands that is executable while the WSM is operating.
See Section 3.3.2.
相關PDF資料 |
PDF描述 |
|---|---|
| 28F200BX-B | 5V or Adjustable, Low-Voltage, Step-Up DC-DC Controller |
| 28F200BX-T | Evaluation Kit for the MAX608 |
| 28F200BL-TB | 2-MBIT (128K x 16, 256K x 8)LOW-POWER BOOT BLOCK FLASH MEMORY FAMILY |
| 28F3204W30 | 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
| 28F320W30 | 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28F200BX-TL/BL | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| 28F200CV-B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| 28F200CV-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| 28F200CV-T/B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SmartVoltage Boot Block Flash Memory Fa |
| 28F256 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:512 Kbit (64Kb x8 Bulk Erase)Flasxh Memory |
發布緊急采購，3分鐘左右您將得到回復。