參數資料
型號： 20668
英文描述： ?lanSC300 Data Sheet ?lanSC310 Data Sheet
中文描述： ？lanSC300數據表？lanSC310數據表
文件頁數： 34/119頁
文件大小： 1167K
代理商： 20668
34
élanSC310 Microcontroller Data Sheet
P R E L I M I N A R Y
DTR/CFG1
Data Terminal Ready (Output; Active Low)
This signal indicates to the external serial device that
the internal serial port controller is ready to communi-
cate.
The state of this signal is used to determine the pin
configuration at power-up. For more information, see
“Alternate Pin Functions” on page 59.
RIN
Ring Indicate (Input; Active Low)
This signal is used as a modem control function. A
change in state on this signal by the external serial de-
vice causes a modem status interrupt. This signal can
be used to cause the élanSC310 microcontroller to re-
sume from a suspended state.
RTS
/CFG0
Request To Send (Output; Active Low)
This signal indicates to the external serial device that
the internal serial port controller is ready to send data.
The state of this signal is used to determine the pin
configuration at power-up. For more information, see
“Alternate Pin Functions” on page 59.
SIN
Serial Data In (Input; Active High)
This signal is used to receive the serial data from the
external serial device into the internal serial port
controller.
SOUT
Serial Data Out (Output; Active High)
This signal is used to transmit the serial data from the
internal serial port controller to the external serial
device.
POWER MANAGEMENT INTERFACE
ACIN
AC Input Status (Input; Active High)
When asserted, this signal disables all power manage-
ment functions (if so enabled). It can be used to indi-
cate when the system is being supplied power from an
AC source.
BL4
–BL1
Battery Low Detects
(Inputs; Negative Edge Sensitive)
These signals are used to indicate to the élanSC310
microcontroller the current status of the battery. BL4–
BL1 can indicate various conditions of the battery as
status changes. A High indicates normal operating
conditions, while a Low indicates a low voltage warning
condition. These inputs can be used to force the sys-
tem into one of the power saving modes when acti-
vated, as follows:
n
BL1 can be programmed to force the system to go
to Low Speed PLL mode or to generate an SMI.
n
BL2 can be programmed to force the system to
enter Sleep mode if not already in Sleep mode, or
to generate an SMI.
n
BL3 can only be programmed to generate an SMI.
n
BL4 can be programmed to force the system to
enter Suspend mode.
EXTSMI
External System Management Interrupt
(Input; Edge Sensitive)
This input is provided to allow external logic to gener-
ate an SMI request to the CPU. It is edge triggered,
with the polarity programmable.
LPH
Latched Power Control (Output; Active Low)
This signal is the inverse of BL4 if ACIN is not true and
BL4 is enabled.
PGP3–PGP0
Programmable Chip Select Generation
(Input/Output)
PGP0 and PGP1 can be programmed as input or out-
put. The default is input. PGP2 and PGP3 are output
only.
These general purpose pins can be individually pro-
grammed as decoder outputs or chip selects for other
external peripheral devices.
PGP0 and PGP2 can be gated with I/O write or act as
an address decode only. PGP1 and PGP3 can be
gated with I/O Read or act as an address decode only.
PGP0 and PGP1 can be directly controlled via a single
register bit if configured to do so. PGP2 and PGP3 can
also be configured for a specific state when the PMU is
in the off state.
PGP2 and PGP3 can be programmed to be set to a
pre-defined state for Micro Power Off mode.
For more information about PGP3–PGP0, see the
élan
TM
SC310 Microcontroller Programmer’s Refer-
ence Manual
, order #20665 and
Using 10-Bit ROMCS
Designs in
élan
TM
SC300 and élanSC310 Microcontrol-
lers Application Note
, order #21825.
PMC4–PMC0
Power Management Controls
(Output; Programmable)
The Power Management Control outputs control the
power to various external devices and system compo-
nents. The PMC0, PMC1, PMC2, and PMC4 signals
相關PDF資料
PDF描述
2067 SAFETY SWITCH FERROCODE
2070 SAFETY SWITCH FERROCODE
2068 SAFETY SWITCH FERROCODE
2068-6104-015 Flange Mount Medium Power Terminations
2068-6119-005 Flange Mount Medium Power Terminations
相關代理商/技術參數
參數描述
20-668-0003 功能描述:微處理器 - MPU Rabbit 2000 Chipset 30MHz RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
20-668-0011 功能描述:微處理器 - MPU Rabbit 3000A LQFP Microprocessor RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
20-668-0016 功能描述:微處理器 - MPU Rabbit 3000 TFBGA Microprocessor RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
2066-8001-90 制造商:TE CONNECTIVITY 功能描述:RF COAXIAL PANEL MOUNT CONNECTOR
20-668-0022 功能描述:微處理器 - MPU Rabbit 4000 LQFP Microprocessor RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*