- 您現在的位置：買賣IC網 > PDF目錄372964 > Z86L9208VSC (ZILOG INC) IR MICROCONTROLLER PDF資料下載
參數資料
| 型號： | Z86L9208VSC |
| 廠商： | ZILOG INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | IR MICROCONTROLLER |
| 中文描述： | 8-BIT, 8 MHz, MICROCONTROLLER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 51/71頁 |
| 文件大小： | 364K |
| 代理商： | Z86L9208VSC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
Z86C72/C92/L72/L92
IR Microcontroller
Zilog
DS97LVO0900
P R E L I M I N A R Y
6-51
1
Power-On Reset (POR).
A timer circuit clocked by a ded-
icated on-board RC oscillator is used for the Power-On Re-
set (POR) timer function. The POR time allows V
CC
and
the oscillator circuit to stabilize before instruction execu-
tion begins.
The POR timer circuit is a one-shot timer triggered by one
of three conditions:
1.
Power Fail to Power OK status.
2.
Stop-Mode Recovery (if D5 of SMR = 1).
3.
WDT Time-Out.
The POR time is a nominal 5 ms. Bit 5 of the Stop-Mode
Register determines whether the POR timer is bypassed
after Stop-Mode Recovery (typical for external clock, RC,
LC oscillators).
HALT.
HALT turns off the internal CPU clock, but not the
XTAL oscillation. The counter/timers and external inter-
rupts IRQ0, IRQ1, IRQ2, IRQ3, and IRQ4 remain active.
The devices are recovered by interrupts, either externally
or internally generated. An interrupt request must be exe-
cuted (enabled) to exit HALT mode. After the interrupt ser-
vice routine, the program continues from the instruction af-
ter the HALT.
STOP.
This instruction turns off the internal clock and ex-
ternal crystal oscillation and reduces the standby current
to 10
μ
A (typical) or less. STOP mode is terminated only
by a reset, such as WDT time-out, POR, SMR, or external
reset. This causes the processor to restart the application
program at address 000CH. In order to enter STOP (or
HALT) mode, it is necessary to first flush the instruction
pipeline to avoid suspending execution in mid-instruction.
To do this, the user must execute a NOP (opcode = FFH)
immediately before the appropriate sleep instruction, i.e.,
FF
6F
NOP
STOP
; clear the pipeline
; enter STOP mode
or
FF
7F
NOP
HALT
; clear the pipeline
; enter HALT mode
Figure 36. Oscillator Configuration
XTAL1
XTAL2
C1
C2
C1
C2
C1
XTAL1
XTAL2
XTAL1
XTAL2
XTAL1
XTAL2
Ceramic Resonator or Crystal
C1, C2 = 47 pF TYP *
f = 8 MHz
LC
C1, C2 = 22 pF
L = 130
μ
H *
f = 3 MHz *
RC
@ 3V VCC (TYP)
C1 = 33 pF *
R = 1K *
External Clock
L
R
* Preliminary value including pin parasitics
C1
32 kHz XTAL
C1 = 20 pF, C = 33 pF
Rd = 56 - 470K
Rf =10 M
Rf
C2
Rd
XTAL1
XTAL2
相關PDF資料 |
PDF描述 |
|---|---|
| Z87200 | CAP 0.047UF 100V 10% X7R AXIAL TR-14 |
| ZA3020 | 2A STEP DOWN PWM SWITCH MODE DC DC REGULATORS |
| ZA3020DS | 2A STEP DOWN PWM SWITCH MODE DC DC REGULATORS |
| ZC0302 | VGA & CIF USB PC Camera Controller |
| ZCN0545A | N-CHANNEL ENHANCEMENT MODE VERTICAL IGBT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Z86L97 | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Low-Voltage Microcontrollers |
| Z86L972 | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Low-Voltage Microcontrollers |
| Z86L972HZ008SC | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Low-Voltage Microcontrollers |
| Z86L972PZ008SC | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Low-Voltage Microcontrollers |
| Z86L973 | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:Low-Voltage Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。