- 您現在的位置：買賣IC網 > PDF目錄376464 > XRT86VL3X_07 (Exar Corporation) Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 PDF資料下載
參數資料
| 型號： | XRT86VL3X_07 |
| 廠商： | Exar Corporation |
| 元件分類： | 通信及網絡 |
| 英文描述： | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| 中文描述： | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| 文件頁數： | 52/153頁 |
| 文件大?。?/td> | 1316K |
| 代理商： | XRT86VL3X_07 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁
XRT86VL3X
45
T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
REV. 1.2.2
4.5
E1 Receive Overhead Interface
4.5.1
Description of the E1 Receive Overhead Output Interface Block
The E1 Receive Overhead Output Interface Block will allow an external device to be the consumer of the E1
National bit sequence. This interface provides interface signals and required interface timing to shift out proper
data link information at proper time.
The Receive Overhead Output Interface for a given Framer consists of two signals.
RxOHClk_n: The Receive Overhead Output Interface Clock Output signal
RxOH_n: The Receive Overhead Output Interface Output signal.
The Receive Overhead Output Interface Clock Output pin (RxOHCLK_n) generates a rising clock edge for
each National bit that is configured to carry Data Link information according to setting of the framer. The data
link bits extracted from the incoming E1 frames are outputted from the Receive Overhead Output Interface
Output pin (RxOH_n) before the rising edge of RxOHClk_n. The Data Link equipment should sample and latch
the data link bits at the rising edge of RxOHClk_n.
The figure below shows block diagram of the Receive Overhead Output Interface of XRT86VL3x.
4.5.2
Configure the E1 Receive Overhead Output Interface module as source of the National Bit
Sequence in E1 framing format mode
The National Bit Sequence in E1 framing format mode can be extracted and directed to:
E1 Receive Overhead Output Interface Block
E1 Receive HDLC Controller
E1 Receive Serial Output Interface
The purpose of the Receive Overhead Output Interface is to permit Data Link equipment to have direct access
to the Sa4 through Sa8 National bits that are extracted from the incoming E1 frames. Independent of the
availability of the E1 Receive HDLC Controller module, the XRT86VL3x always output the received National
bits through the Receive Overhead Output Interface block.
The XRT86VL3x allows the user to decide on the following:
How many of the National Bits is used to carry the Data Link information bits
Which of these National Bits is used to carry the Data Link information bits.
The Receive Sa Data Link Select bits of the Receive Signaling and Data Link Select Register (TSDLSR)
determine which ones of the National bits are configured as Data Link bits in E1 framing format mode.
Depending upon the configuration of the Receive Signaling and Data Link Select Register, either of the
following cases may exists:
None of the received National bits are used to transport the Data Link information bits (That is, data link
channel of XRT86VL3x is inactive).
Any combination of between 1 and all 5 of the received National bits are used to transport the Data Link
information bits.
F
IGURE
44. B
LOCK
D
IAGRAM
OF
THE
E1 R
ECEIVE
O
VERHEAD
O
UTPUT
I
NTERFACE
OF
XRT86VL3
X
Receive
Overhead Output
Interface
RxOH_n
RxOHClk_n
From Receive
Framer Block
相關PDF資料 |
PDF描述 |
|---|---|
| XRT86VL3X | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| XRT91L30_0611 | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
| XRT91L306 | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
| XRT91L30IQ | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
| XRT91L30 | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT86VX38 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION |
| XRT86VX38_09 | 制造商:EXAR 制造商全稱:EXAR 功能描述:8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION |
| XRT86VX38_0906 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION |
| XRT86VX38IB256 | 制造商:EXAR 制造商全稱:EXAR 功能描述:8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - E1 REGISTER DESCRIPTION |
| XRT86VX38IB256ES | 功能描述:界面開發工具 Evaluation Board for XRT86VX38 256pin ICs RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。