參數資料
型號： XRT86VL34_2
廠商： Exar Corporation
元件分類： 通信及網絡
英文描述： Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
中文描述： Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
文件頁數： 142/156頁
文件大?。?/td> 816K
代理商： XRT86VL34_2
XRT86VL34
137
QUAD T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
REV. V1.2.0
3
NLCD_n
RO
0
Network Loop-Code Detection Status Bit:
This bit operates differently in the Manual or the Automatic Network
Loop-Code detection modes.
Manual Loop-Up Code detection mode
(.i.e If NLCDE1 = “0” and NLCDE0 = “1”), this bit gets set to “1” as
soon as the Loop-Up Code (“00001”) is detected in the receive data
for longer than 5 seconds.
This bit stays high as long as the Receive T1 LIU Block detects the
presence of the Loop-Up code in the receive data and it is reset to
“0” as soon as it stops receiving the Loop-Up Code.
If the NLCD interrupt is enabled, the XRT86VL34 will initiate an
interrupt on every transition of the NLCD status bit.
Manual Loop-Down Code detection mode
(i.e., If NLCDE1 = “1” and NLCDE0 = “0”), this bit gets set to “1” as
soon as the Loop-Down Code (“001”) is detected in the receive data
for longer than 5 seconds.
This bit stays high as long as the Receive T1 LIU Block detects the
presence of the Loop-Down code in the receive data and it is reset
to “0” as soon as it stops receiving the Loop-Down Code.
If the NLCD interrupt is enabled, the XRT86VL34 will initiate an
interrupt on every transition of the NLCD status bit.
Automatic Loop-code detection mode
(i.e., If NLCDE1 = “1” and NLCDE0 =”1”), the state of the NLCD sta-
tus bit is reset to “0” and the XRT86VL34 is programmed to monitor
the receive input data for the Loop-Up code.
This bit is set to a “1” to indicate that the Network Loop Code is
detected for more than 5 seconds. Simultaneously, the Remote
Loop-Back condition is automatically activated and the XRT86VL34
is programmed to monitor the receive data for the Network Loop
Down code. The NLCD bit stays ‘high’ as long as the Remote Loop-
Back condition is in effect even if the chip stops receiving the Loop-
Up code. Remote Loop-Back is removed only if the XRT86VL34
detects the Loop-Down Code “001” pattern for longer than 5 sec-
onds in the receive data. Upon detecting the Loop-Down Code “001”
pattern, the XRT86VL34 will reset the NLCD status bit and an inter-
rupt will be generated if the NLCD interrupt enable bit is enabled.
Users can monitor the state of this bit to determine if the Remote
Loop-Back is activated.
2
Reserved
-
0
This Bit Is Not Used
1
RLOS_n
RO
0
Receive Loss of Signal Defect Condition Status:
This READ-ONLY bit indicates whether or not the Receive LIU Block
is currently declaring the LOS defect condition.
0 = Indicates that the Receive Section is NOT currently declaring
the LOS Defect Condition.
1 = Indicates that the Receive Section is currently declaring the LOS
Defect condition.
N
OTE
:
If the RLOSIE bit (bit D1 of Register 0x0Fn4) is enabled, any
transition on this bit will generate an Interrupt.
T
ABLE
112: LIU C
HANNEL
C
ONTROL
S
TATUS
R
EGISTER
(LIUCCSR) H
EX
A
DDRESS
: 0
X
0F
N
5
B
IT
F
UNCTION
T
YPE
D
EFAULT
D
ESCRIPTION
-O
PERATION
相關PDF資料
PDF描述
XRT86VL34IB Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT86VL38_2 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT86VL38IB Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT86VL38IB484 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT86VL38_07 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
相關代理商/技術參數
參數描述
XRT86VL34ES 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT86VL34IB 功能描述:網絡控制器與處理器 IC 4 IND FULL DPLX FIFO TWO-FRAME, CAS, CCS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT86VL34IB-F 功能描述:網絡控制器與處理器 IC 4-Ch T1/E1/J1 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT86VL38 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
XRT86VL38_07 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - E1 REGISTER DESCRIPTION
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*