參數資料
型號: XRT75VL00D
廠商: Exar Corporation
英文描述: E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
中文描述: E3/DS3/STS-1線路接口單元與SONET DESYNCHRONIZER
文件頁數: 80/92頁
文件大?。?/td> 836K
代理商: XRT75VL00D
XRT75VL00D
REV. 1.0.3
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
76
9.7.2
Wander Measurement Test Results
Wander Measurement test results will be provided in the next revision of the LIU Data Sheet.
9.8
Designing with the LIU
In this section, we will discuss the following topics.
How to design with and configure the LIU to permit a system to meet the above-mentioned Intrinsic Jitter and
Wander requirements.
How is the LIU able to meet the above-mentioned requirements?
How does the LIU permits the user to comply with the SONET APS Recovery Time requirements of 50ms
(per Telcordia GR-253-CORE)?
How should one configure the LIU, if one needs to support "Daisy-Chain" Testing at the end Customer’s site?
9.8.1
How to design and configure the LIU to permit a system to meet the above-mentioned
Intrinsic Jitter and Wander requirements
As mentioned earlier, in most application (in which the LIU will be used in a SONET De-Sync Application) the
user will typically interface the LIU to a Mapper device in the manner as presented below in Figure 57.
In this application, the Mapper has the responsibility of receiving a SONET STS-N/OC-N signal and extracting
as many as N DS3 signals from this signal. As a given channel within the Mapper IC extracts out a given DS3
signal (from SONET) it will typically be applying a Clock and Data signal to the "Transmit Input" of the LIU IC.
Figure 57 presents a simple illustration as to how one channel, within the LIU should be connected to the
Mapper IC.
As mentioned above, the Mapper IC will typically output a Clock and Data signal to the LIU. In many cases,
the Mapper IC will output the contents of an entire STS-1 data-stream via the Data Signal to the LIU. However,
the Mapper IC typically only supplies a clock pulse via the Clock Signal to the LIU coincident to whenever a
DS3 bit is being output via the Data Signal. In this case, the Mapper IC would not supply a clock edge
coincident to when a TOH, POH or any non-DS3 data-bit is being output via the Data-Signal.
Figure 57 indicates that the Data Signal from the Mapper device should be connected to the TPDATA_n input
pin of the LIU IC and that the Clock Signal from the Mapper device should be connected to the TCLK_n input
pin of the LIU IC.
In this application, the LIU has the following responsibilities.
FIGURE 57. ILLUSTRATION OF THE LIU BEING CONNECTED TO A MAPPER IC FOR SONET DE-SYNC APPLICATIONS
DS3 to STS-N
Mapper/
Demapper
IC
DS3 to STS-N
Mapper/
Demapper
IC
LIU
STS-N Signal
TPDATA_n input pin
TCLK n input
De-Mapped (Gapped)
DS3 Data and Clock
相關PDF資料
PDF描述
XRT83SL34IV QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83SL34 QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XS2F-A422-90-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
XS2F-A422-A90-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
XS2F-A422-AB0-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
相關代理商/技術參數
參數描述
XRT75VL00D_08 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET
XRT75VL00D1V-F 制造商:Exar Corporation 功能描述:
XRT75VL00DES 功能描述:時鐘合成器/抖動清除器 1CHT3/E3/STS1LIU+ DESYNC 3.3V DRV VER RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75VL00DIV 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75VL00DIV-F 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel