參數資料
型號: XRT75VL00D
廠商: Exar Corporation
英文描述: E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
中文描述: E3/DS3/STS-1線路接口單元與SONET DESYNCHRONIZER
文件頁數: 25/92頁
文件大?。?/td> 836K
代理商: XRT75VL00D
XRT75VL00D
REV. 1.0.3
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
26
For E3 mode, the pulse shaper converts the HDB3 encoded pulses into a single full amplitude square shaped
pulse with very little slope. This is illustrated in Figure 7.
The Pulse Shaper Block also consists of a Transmit Build Out Circuit, which can either be disabled or enabled
by setting the TxLEV input pin “High” or “Low” (in Hardware Mode) or setting the TxLEV bit to “1” or “0” in the
control register (in Host Mode).
For DS3/STS-1 rates, the Transmit Build Out Circuit is used to shape the transmit waveform that ensures that
transmit pulse template requirements are met at the Cross-Connect system. The distance between the
transmitter output and the Cross-Connect system can be between 0 to 450 feet.
For E3 rate, since the output pulse template is measured at the secondary of the transformer and since there is
no Cross-Connect system pulse template requirements, the Transmit Build Out Circuit is always disabled.
4.3.1
Guidelines for using Transmit Build Out Circuit:
If the distance between the transmitter and the DSX3 or STSX-1, Cross-Connect system, is less than 225 feet,
enable the Transmit Build Out Circuit by setting the TxLEV input pin “Low” (in Hardware Mode) or setting the
TxLEV control bit to “0” (in Host Mode).
If the distance between the transmitter and the DSX3 or STSX-1 is greater than 225 feet, disable the Transmit
Build Out Circuit.
4.3.2
Interfacing to the line:
The differential line driver increases the transmit waveform to appropriate level and drives into the 75
load as
shown in Figure 6.
4.4
Transmit Drive Monitor:
This feature is used for monitoring the transmit line for occurrence of fault conditions such as short circuit on
the line or defective line driver.The device can also be configured for internal tranmit driver monitoring.
To monitor the transmitter output of another chip, connect MTIP pin to the TTIP line via a 270
resistor and
MRing pins to TRing line via 270
resistor as shown in Figure 16
In order to configure the device for internal transmit driver monitoring, set the TxMON bit to “1” in the transmit
control register.
FIGURE 16. TRANSMIT DRIVER MONITOR SET-UP.
3.
3k
+
1
%
TT I P
TR i n g
X R T75V L00
1: 1
R3
75
Tx PO S
Tx N E G
Tx L in e C lk
TP D a t a
T NDa t a
Tx C lk
Re x t
Re f A GND
31. 6
+ 1%
31 . 6
+1%
R1
R2
MR i n g
MT I P
R5 2 7 0
R4 2 7 0
3.
3k
+
1
%
Tx P O S
Tx N E G
T x Li ne C l k
TPD a t a
TN D a t a
Tx C lk
Re x t
Re f A G N D
MR i n g
MT I P
TTI P
TR i n g
R3
75
31. 6
+ 1%
31. 6
+1%
R1
R2
1: 1
相關PDF資料
PDF描述
XRT83SL34IV QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83SL34 QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XS2F-A422-90-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
XS2F-A422-A90-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
XS2F-A422-AB0-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
相關代理商/技術參數
參數描述
XRT75VL00D_08 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET
XRT75VL00D1V-F 制造商:Exar Corporation 功能描述:
XRT75VL00DES 功能描述:時鐘合成器/抖動清除器 1CHT3/E3/STS1LIU+ DESYNC 3.3V DRV VER RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75VL00DIV 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75VL00DIV-F 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel