參數資料
型號: XRT73R12
廠商: Exar Corporation
英文描述: TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
中文描述: 第十二章通道E3/DS3/STS-1線路接口單元
文件頁數: 49/87頁
文件大?。?/td> 436K
代理商: XRT73R12
PRELIMINARY
XRT73R12
REV. P1.0.3
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
46
7.1
The LIU may be configured into different operating modes and have its performance monitored by software
through a standard microprocessor using data, address and control signals. These interface signals are de-
scribed below in Table 13. The microprocessor interface can be configured to operate in Asynchronous mode
or Synchronous mode.
T
HE
M
ICROPROCESSOR
I
NTERFACE
B
LOCK
S
IGNALS
T
ABLE
13: XRT73R12 M
ICROPROCESSOR
I
NTERFACE
S
IGNALS
P
IN
N
AME
T
YPE
D
ESCRIPTION
Pmode
I
Microprocessor Interface Mode Select Input pin
This pin is used to specify the microprocessor interface mode.
D[7:0]
I/O
Bi-Directional Data Bus for register "Read" or "Write" Operations.
Addr[7:0]
I
Eight-Bit Address Bus Inputs
The XRT73R12 LIU microprocessor interface uses a direct address bus. This address bus is
provided to permit the user to select an on-chip register for Read/Write access.
CS
I
Chip Select Input
This active low signal selects the microprocessor interface of the XRT73R12 LIU and enables
Read/Write operations with the on-chip register locations.
RD
I
Read Signal
This active low input functions as the read signal from the local
μ
P. When this
pin is pulled “Low” (if CS is “Low”) the LIU is informed that a read operation has been
requested and begins the process of the read cycle.
WR
I
Write Signal
This active low input functions as the write signal from the local
μ
P. When this
pin is pulled “Low” (if CS is “Low”) the LIU is informed that a write operation has been
requested and begins the process of the write cycle.
RDY
O
Ready Output
This active low signal is provided by the LIU device. It indicates that the cur-
rent read or write cycle is complete, and the LIU is waiting for the next command.
INT
O
Interrupt Output
This active low signal is provided by the LIU to alert the local mP that a
change in alarm status has occured. This pin is Reset Upon Read (RUR) once the alarm sta-
tus registers have been cleared.
RESET
I
Reset Input
This active low input pin is used to Reset the LIU.
相關PDF資料
PDF描述
XRT73R12IB TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT74L73 3 CHANNEL, ATM UNI/PPP DS3/E3 FRAMING CONTROLLER
XRT74L73IB 3 CHANNEL, ATM UNI/PPP DS3/E3 FRAMING CONTROLLER
XRT74L74 4 CHANNEL, ATM UNI/PPP DS3/E3 FRAMING CONTROLLER
XRT74L74IB 4 CHANNEL, ATM UNI/PPP DS3/E3 FRAMING CONTROLLER
相關代理商/技術參數
參數描述
XRT73R12_07 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R12_0710 制造商:EXAR 制造商全稱:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R12ES 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT73R12IB 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73R12IB-F 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray