- 您現在的位置：買賣IC網 > PDF目錄376461 > XRT73L02M (Exar Corporation) TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT PDF資料下載
參數資料
| 型號： | XRT73L02M |
| 廠商： | Exar Corporation |
| 英文描述： | TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
| 中文描述： | 雙通道E3/DS3/STS-1線路接口單元 |
| 文件頁數： | 27/46頁 |
| 文件大小： | 391K |
| 代理商： | XRT73L02M |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
xr
XRT73L02M
TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.0.0
4.0.3
The Transmit Pulse Shaper converts the B3ZS encoded digital pulses into a single analog Alternate Mark In-
version (AMI) pulse that meet the industry standard mask template requirements for STS-1 and DS3. See Fig-
ures 8 and 9.
For E3 mode, the pulse shaper converts the HDB3 encoded pulses into a single full amplitude square shaped
pulse with very little slope. This is illustrated in Figure 7.
The Pulse Shaper Block also includes a Transmit Build Out Circuit, which can either be disabled or enabled by
setting the TxLEV_n input pin “High” or “Low” (in Hardware Mode) or setting the TxLEV_n bit to “1” or “0” in the
control register (in Host Mode).
For DS3/STS-1 rates, the Transmit Build Out Circuit is used to shape the transmit waveform that ensures that
transmit pulse template requirements are met at the Cross-Connect system. The distance between the trans-
mitter output and the Cross-Connect system can be between 0 to 450 feet.
For E3 rate, since the output pulse template is measured at the secondary of the transformer and since there is
no Cross-Connect system pulse template requirements, the Transmit Build Out Circuit is always disabled.
4.0.3.1
Guidelines for using Transmit Build Out Circuit:
If the distance between the transmitter and the DSX3 or STSX-1, Cross-Connect system, is less than 225 feet,
enable the Transmit Build Out Circuit by setting the TxLEV_n input pin “Low” (in Hardware Mode) or setting the
TxLEV_n control bit to “0” (in Host Mode).
If the distance between the transmitter and the DSX3 or STSX-1 is greater than 225 feet, disable the Transmit
Build Out Circuit.
4.0.3.2
Interfacing to the line:
The differential line driver increases the transmit waveform to appropriate level and drives into the 75
load as
shown in Figure 6.
4.0.4
Transmit Drive Monitor:
This feature is used for monitoring the transmit line for occurrence of fault conditions such as a short circuit on
the line or a defective line driver.
To activate this function, connect MTIP_n pins to the TTIP_n lines via a 270
resistor and MRing_n pins to
TRING_n lines via 270
resistor as shown in Figure 16.
25
T
RANSMIT
P
ULSE
S
HAPER
:
F
IGURE
16. T
RANSMIT
D
RIVER
M
ONITOR
SET
-
UP
.
3
TTIP(n)
TRING(n)
XRT73L02M (0nly one channel shown)
1:1
R3
75
TxPOS(n)
TxNEG(n)
TxLineClk(n)
TPOS(n)
TNEG(n)
TxCLK(n)
RxB
RxA
31.6
+ 1%
31.6
+1%
R1
R2
MRING(n)
MTIP(n)
R5 270
R4 270
相關PDF資料 |
PDF描述 |
|---|---|
| XRT73L02MIV | TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L02 | 2 Channel E3/DS3/STS-1 Line Interface Unit(2通道 E3/DS3/STS-1線接口單元) |
| XRT73L03A | 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73L03AIV | 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73L03B | 3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT73L02MES | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT73L02MIV | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L02MIV-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT73L02MIVTR-F | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT73L03 | 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL E3/DS3/STS-1 LINE INTERFCE UNIT |
發布緊急采購，3分鐘左右您將得到回復。