- 您現在的位置：買賣IC網 > PDF目錄376460 > XRT4000 (Exar Corporation) Universal Multiprotocol Serial Interface PDF資料下載
參數資料
| 型號： | XRT4000 |
| 廠商： | Exar Corporation |
| 英文描述： | Universal Multiprotocol Serial Interface |
| 中文描述： | 通用多協議串行接口 |
| 文件頁數： | 21/46頁 |
| 文件大?。?/td> | 396K |
| 代理商： | XRT4000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
XRT4000
Rev. 1.00
- 21 -
Clock Inversion
Transmit Clock signal, TXC, has an inversion
option for both DTE and DCE modes of
operation. The user can invert the polarity of the
TXC by setting CKINV* to logic 0. In the DTE
mode, the incoming TXC signal from the line will
be inverted before it is routed to the system. In
DCE mode, the incoming TXC signal from the
system will be inverted before it is sent over the
line toward the remote DTE. This feature allows
a phase correction when there is a long cable
delay between the DTE and DCE. This
correction may be necessary in order to obtain
the desired clock-to-data phase relationship.
Data Inversion
Similar to TXC, there is a provision in the
XRT4000 to invert the TXD and RXD signals.
Once the Setting the DTINV* input to logic 0
enables an inverter at the output of RX1 and
input of TX1.
Registered Mode of Operation
The XRT4000 has integrated registers allowing
users the option of clocking the values of
DSR/DTR and RL/RI signals. This can be done
if the registered mode of operation is selected
(REG=1). In this case, the values of these
signals will be latched on the positive edge of
the REG_CLK signal. In the normal mode (REG
= 0), the registers on the path of the DSR/DTR
and RL/RI are bypassed and REG_CLK will
have no effect.
Similarly, the outputs of the receivers (RX5 and
RX8) can be disabled by setting the EN_OUT*
input high. This allows these drivers to be
connected directly to a microcontroller bus since
they can be enabled during read cycles and
disabled in other times.
This feature eliminates the need for external
registers when a microcontroller is used to
control (reading and writing) DSR/DTR and
RL/RI signals.
Loopbacks
XRT4000 contains internal logic to place the
interface in a loopback mode for test purposes.
The loopback feature is supported in both DTE
and DCE modes of operation and it can be
invoked by setting the LP* input at logic 0.
Possible loopback implementations are depicted
in the scenarios located at the end of this
document.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT4500 | MULTIPROTOCOL SERIAL NETWORK INTERFACE IC |
| XRT4500CV | MULTIPROTOCOL SERIAL NETWORK INTERFACE IC |
| XRT56L85 | Low Power PCM Line Interface |
| XRT5794ES | Evaluation System |
| XRT5894ES | () |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT4000CV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Transceiver |
| XR-T445B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XRT4500 | 制造商:EXAR 制造商全稱:EXAR 功能描述:MULTIPROTOCOL SERIAL NETWORK INTERFACE IC |
| XRT4500CV | 制造商:EXAR 制造商全稱:EXAR 功能描述:MULTIPROTOCOL SERIAL NETWORK INTERFACE IC |
| XR-T5600P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM Repeater |
發布緊急采購，3分鐘左右您將得到回復。