參數資料
型號: XR20M1172L32-0B-EB
廠商: Exar Corporation
文件頁數: 33/55頁
文件大?。?/td> 0K
描述: EVAL BOARD FOR XR20M1172 32QFN
標準包裝: 1
主要目的: 接口,UART
嵌入式:
已用 IC / 零件: XR20M1172
主要屬性: 2 通道
次要屬性: I²C & SPI 接口
已供物品:
其它名稱: 1016-1625
XR20M1172L32-0B-EB-ND
XR20M1172
39
REV. 1.2.0
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
4.19
Extra Features Control Register (EFCR) - Read/Write
EFCR[7]: IrDA mode
This bit selects between the slow and fast IrDA modes. See “Section 2.15, Infrared Mode” on page 22 for
complete details.
Logic 0 = IrDA version 1.0, 3/16 pulse ratio, data rate up to 115.2 Kbps
Logic 1 = IrDA version 1.1, 1/4 pulse ratio, data rate up to 1.152 Mbps
EFCR[6]: Reserved
EFCR[5]: Auto RS-485 Polarity Inversion
This bit changes the polarity of the Auto RS-485 Half-Duplex Direction Control output (RTS#). This bit will only
affect the behavior of the RTS# output if EFCR[4] = 1. See “Section 2.14, Auto RS485 Half-duplex Control”
on page 20 for complete details.
Logic 0 = RTS# output is LOW when transmitting and HIGH when receiving.
Logic 1 = RTS# output is HIGH when transmitting and LOW when receiving.
EFCR[4]: Auto RS-485 Enable
This bit enables the RTS# output as the Auto RS-485 Half-Duplex Direction Control output. See “Section
2.14, Auto RS485 Half-duplex Control” on page 20 for complete details.
Logic 0 = RTS# output can be used for Auto RTS Hardware Flow Control or as a general purpose output.
Logic 1 = RTS# output enabled as the Auto RS-485 Half-Duplex Direction Control output.
EFCR[3]: Reserved
EFCR[2]: Transmitter Disable
UART does not send serial data out on the TX output pin, but the TX FIFO will continue to receive data from
CPU until full. Any data in the TSR will be sent out before the trasnmitter goes into disable state.
Logic 0 = Transmitter is enabled
Logic 1 = Transmitter is disabled
EFCR[1] = Receiver Disable
UART will stop receiving data immediately once this bit is set to a Logic 1. Any data that is being received in
the TSR will be received correctly and sent to the RX FIFO.
Logic 0 = Receiver is enabled
Logic 1 = Receiver is disabled
EFCR[0]: 9-bit or Multidrop Mode Enable
This bit enables 9-bit or Multidrop mode. See “Section 2.14, Auto RS485 Half-duplex Control” on page 20
for complete details.
Logic 0 = Normal 8-bit mode
Logic 1 = Enable 9-bit or Multidrop mode
4.20
Baud Rate Generator Registers (DLL, DLM and DLD[3:0]) - Read/Write
These registers make-up the value of the baud rate divisor. The concatenation of the contents of DLM and
DLL is a 16-bit value is then added to DLD[3:0]/16 to achieve the fractional baud rate divisor. DLD must be
enabled via EFR bit-4 before it can be accessed. SEE”PROGRAMMABLE BAUD RATE GENERATOR WITH
FRACTIONAL DIVISOR” ON PAGE 13.
相關PDF資料
PDF描述
XR20M1170L16-0B-EB EVAL BOARD FOR XR20M1170 16QFN
RPP30-4824S-1F CONV DC/DC 30W 36-75VIN 24VOUT
462A023-4/86-0 BOOT MOLDED
MLF2012E6R8J INDUCTOR MULTILAYER 6.8UH 0805
XR20M1170G24-0B-EB EVAL BOARD FOR XR20M1170 24TSSOP
相關代理商/技術參數
參數描述
XR20M1280 制造商:EXAR 制造商全稱:EXAR 功能描述:I2C/SPI UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
XR20M1280IL24-F 功能描述:UART 接口集成電路 1Ch 12C/SPI UART w/ Lvl Shftrs & 4 GPIOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1280IL24TR-F 功能描述:UART 接口集成電路 1Ch 12C/SPI UART w/ Lvl Shftrs & 4 GPIOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1280IL32-F 功能描述:UART 接口集成電路 1Ch 12C/SPI UART w/ Lvl Shftrs & 8 GPIOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1280IL32TR-F 功能描述:UART 接口集成電路 1Ch 12C/SPI UART w/ Lvl Shftrs & 8 GPIOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel