參數資料
型號： XR20M1172L32-0B-EB
廠商： Exar Corporation
文件頁數： 29/55頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR20M1172 32QFN
標準包裝： 1
主要目的： 接口，UART
嵌入式： 否
已用 IC / 零件： XR20M1172
主要屬性： 2 通道
次要屬性： I²C & SPI 接口
已供物品： 板
其它名稱： 1016-1625
XR20M1172L32-0B-EB-ND
XR20M1172
35
REV. 1.2.0
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
MCR[7]: Clock Prescaler Select (requires EFR bit-4=1 to write to this bit)
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
4.8
Line Status Register (LSR) - Read Only
This register provides the status of data transfers between the UART and the host.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
LSR[1]: Receiver Overrun Error Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[2]: Receive Data Parity Error Tag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR.
LSR[3]: Receive Data Framing Error Tag
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
LSR[4]: Receive Break Error Tag
Logic 0 = No break condition (default).
Logic 1 = The receiver received a break signal (RX was LOW for at least one character frame time). In the
FIFO mode, only one break character is loaded into the FIFO.
LSR[5]: Transmit Holding Register Empty Flag
This bit is the Transmit Holding Register Empty indicator. The THR bit is set to a logic 1 when the last data byte
is transferred from the transmit holding register to the transmit shift register. The bit is reset to logic 0
concurrently with the data loading to the transmit holding register by the host. In the FIFO mode this bit is set
when the transmit FIFO is empty, it is cleared when the transmit FIFO contains at least 1 byte.
LSR[6]: THR and TSR Empty Flag
This bit is set to a logic 1 whenever the transmitter goes idle. It is set to logic 0 whenever either the THR or
TSR contains a data character. In the FIFO mode this bit is set to a logic 1 whenever the transmit FIFO and
transmit shift register are both empty.
相關PDF資料
PDF描述
XR20M1170L16-0B-EB EVAL BOARD FOR XR20M1170 16QFN
RPP30-4824S-1F CONV DC/DC 30W 36-75VIN 24VOUT
462A023-4/86-0 BOOT MOLDED
MLF2012E6R8J INDUCTOR MULTILAYER 6.8UH 0805
XR20M1170G24-0B-EB EVAL BOARD FOR XR20M1170 24TSSOP
相關代理商/技術參數
參數描述
XR20M1280 制造商:EXAR 制造商全稱:EXAR 功能描述:I2C/SPI UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS
XR20M1280IL24-F 功能描述:UART 接口集成電路 1Ch 12C/SPI UART w/ Lvl Shftrs & 4 GPIOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1280IL24TR-F 功能描述:UART 接口集成電路 1Ch 12C/SPI UART w/ Lvl Shftrs & 4 GPIOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1280IL32-F 功能描述:UART 接口集成電路 1Ch 12C/SPI UART w/ Lvl Shftrs & 8 GPIOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1280IL32TR-F 功能描述:UART 接口集成電路 1Ch 12C/SPI UART w/ Lvl Shftrs & 8 GPIOs RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*