REV. 1.1.0 MCR[2]: OP1# / TCR and TLR Enable OP1# is not available as an output pin on the M1170. B" />
參數資料
型號： XR20M1170L24-0B-EB
廠商： Exar Corporation
文件頁數： 26/56頁
文件大小： 0K
描述： EVAL BOARD FOR XR20M1170 24QFN
標準包裝： 1
主要目的： 接口，UART
嵌入式： 否
已用 IC / 零件： XR20M1170
次要屬性： I²C & SPI 接口
已供物品： 板
其它名稱： 1016-1621
XR20M1170L24-0B-EB-ND
XR20M1170
32
I2C/SPI UART WITH 64-BYTE FIFO
REV. 1.1.0
MCR[2]: OP1# / TCR and TLR Enable
OP1# is not available as an output pin on the M1170. But it is available for use during Internal Loopback Mode
(MCR[4] = 1). In the Internal Loopback Mode, this bit is used to write the state of the modem RI# interface
signal.
This bit is also used to select between the MSR and TCR registers at address offset 0x6 and the SPR and TLR
registers at address offset 0x7. Table 12 and Table 13 below shows how these registers are accessed.
TABLE 12: REGISTER AT ADDRESS OFFSET 0X6
EFR[4] MCR[2] Register at Address Offset 0x6
0
X
Modem Status Register (MSR)
1
0
Modem Status Register (MSR)
1
Trigger Control Register (TCR)
TABLE 13: REGISTER AT ADDRESS OFFSET 0X7
EFR[4] MCR[2] Register at Address Offset 0x7
0
X
Scratchpad Register (SPR)
1
0
Scratchpad Register (SPR)
1
Trigger Level Register (TLR)
MCR[3]: OP2#
OP2# is not available as an output on the M1170 but can be controlled in internal loopback mode.
Logic 0 = OP2# set HIGH(default).
Logic 1 = OP2# set LOW.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 19.
MCR[5]: Xon-Any Enable (requires EFR bit-4=1 to write to this bit)
Logic 0 = Disable Xon-Any function (default).
Logic 1 = Enable Xon-Any function. In this mode, any RX character received will resume transmit operation.
The RX character will be loaded into the RX FIFO, unless the RX character is an Xon or Xoff character and
the M1170 is programmed to use the Xon/Xoff flow control.
MCR[6]: IR Mode Enable (requires EFR bit-4=1 to write to this bit)
This bit enables the infrared mode and/or controls the infrared mode after power-up. See “Section 2.15,
Infrared Mode” on page 20 for complete details.
Logic 0 = Reserved (default).
Logic 1 = Enable IR Mode.
相關PDF資料
PDF描述
RPP30-4824S CONV DC/DC 30W 36-75VIN 24VOUT
RPP30-2424S-F CONV DC/DC 30W 18-36VIN 24VOUT
MLF2012A4R7J INDUCTOR MULTILAYER 4.7UH 0805
XR20M1170L16-0A-EB EVAL BOARD FOR XR20M1170 16QFN
GBM12DSAI CONN EDGECARD 24POS R/A .156 SLD
相關代理商/技術參數
參數描述
XR20M1170L28-0A-EB 功能描述:UART 接口集成電路 Supports M1170 28pin QFN, I2C Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1170L28-0B-EB 功能描述:界面開發工具 Supports M1170 28pin QFN, SPI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR20M1172 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
XR20M1172_09 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
XR20M1172G28-0A-EB 功能描述:UART 接口集成電路 Supports M1172 28 ld TSSOP, I2C Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*