- 您現在的位置：買賣IC網 > PDF目錄3762 > XR19L400IL40TR-F (Exar Corporation)IC UART/TXRX RS485 40QFN PDF資料下載
參數資料
| 型號： | XR19L400IL40TR-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 34/46頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART/TXRX RS485 40QFN |
| 標準包裝： | 3,000 |
| 特點： | * |
| 通道數： | 1，UART |
| FIFO's： | 64 字節 |
| 規程： | RS485 |
| 電源電壓： | 3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-QFN 裸露焊盤（6x6） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
XR19L400
4
SINGLE CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER
REV. 1.0.3
NOTE: Pin type: I=Input, O=Output, I/O= Input/output, OD=Output Open Drain. For CMOS/TTL Voltage levels, ’LOW’
indicates a voltage in the range 0V to VIL and ’HIGH" indicates a voltage in the range VIH to VCC.
XTAL2
13
O
Crystal or buffered clock output.
PwrSave
11
I
Power-Save (active high). This feature isolates the L400’s data bus interface from the host
preventing other bus activities that cause higher power drain during sleep mode.
ACP
19
I
Autosleep for Charge Pump (active HIGH). When the power supply is 3.3V, this pin shuts off
the charge pump if the UART is already in sleep mode, i.e. the XTAL2 output is LOW. When
the power supply is 5V, this pin should be connected to GND.
I/M#
17
I
Intel or Motorola Bus Select.
When I/M# pin is HIGH, 16 or Intel Mode, the device will operate in the Intel bus type of
interface.
When I/M# pin is LOW, 68 or Motorola mode, the device will operate in the Motorola bus
type of interface.
RESET
(RESET#)
18
I
When I/M# pin is HIGH for Intel bus interface, this input becomes RESET (active high).
When I/M# pin is LOW for Motorola bus interface, this input becomes RESET# (active low).
A 40 ns minimum active pulse on this pin will reset the internal registers and all outputs of
the UART. The UART transmitter output will be held HIGH, the receiver input will be ignored
and outputs are reset during reset period.
C1-
C1+
25
26
-
Charge pump capacitors. As shown in
Figure 1, a 0.22 uF capacitor should be placed
between these 2 pins.
R_EN
20
I
Regulator Enable. This pin regulates the 5V VCC down to 3.3V internally for the UART.
When the supply voltage is 3.3V, connect R_EN to GND.
When the supply voltage is 5V, connect R_EN to VCC.
TEST0
TEST1
TEST2
35
36
10
I
Factory Test Modes. For normal operation, these pins must be connected to GND.
VCC33
21
Pwr 3.3V power supply. When VCC33 is used, R_EN pin should be connected to GND.
A 0.1 uF capacitor to GND is recommended on this power supply pin. If VCC33 is not used
as the power supply pin, VCC33 should be left unconnected. See
Figure 3. All CMOS/
TTL input pins, except XTAL1, are 5V tolerant.
VCC50
33
Pwr 5.0V power supply. When VCC50 is used, R_EN pin should be connected to VCC.
A 1uF capacitor to GND is recommended on the VCC50 power supply pin. The 1uF capac-
itor is recommended whether VCC33 or VCC50 is used as the power supply pin. See
Figure 3. All CMOS/TTL input pins, except XTAL1, are 5V tolerant.
GND
31
Pwr Power supply common, ground.
-
PAD
Pwr The center pad on the backside of the QFN package is metallic and is not electrically con-
nected to anything inside the device. It must be soldered on to the PCB and may be option-
ally connected to GND on the PCB. The thermal pad size on the PCB should be the
approximate size of this center pad and should be solder mask defined. The solder mask
opening should be at least 0.0025" inwards from the edge of the PCB thermal pad.
NC
16, 22, 23,
24, 29
-
No Connect. Note that in Motorola mode, the IOR# pin also becomes an NC pin.
Pin Descriptions
NAME
40-QFN
PIN#
TYPE
DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| XR16M680IB25-F | IC UART FIFO 32B 25BGA |
| XR16M670IB25-F | IC UART FIFO 32B 25BGA |
| XR20M1170IL16TR-F | IC UART FIFO I2C/SPI 64B 16QFN |
| XR16M580IB25-F | IC UART FIFO 16B 25BGA |
| XR16M570IB25-F | IC UART FIFO 16B 25BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR19L402 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402_09 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402IL48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402IL48-0B-EB | 功能描述:界面開發工具 Supports L402 48 pin QFN, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR19L402IL48-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。