參數資料
型號： XR19L220IL40-0B-EB
廠商： Exar Corporation
文件頁數： 19/43頁
文件大小： 0K
描述： EVAL BOARD FOR XR19L202 40QFN
標準包裝： 1
系列： *
XR19L220
26
SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
REV. 1.0.2
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced LOW).
This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) LOW for alerting the remote receiver of a line break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.8
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR Output
The DTR pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR output HIGH (default).
Logic 1 = Force DTR output LOW.
MCR[1]: RTS Output
The RTS pin is a modem control output and may be used for automatic hardware flow control by enabled by
EFR bit-6. If the modem interface is not used, this output may be used as a general purpose output.
Logic 0 = Force RTS output HIGH (default).
Logic 1 = Force RTS output LOW.
MCR[2]: OP1# (legacy term)
The OP1# output does not come out on the XR19L220, however, it is available in internal loopback. In the
Internal Loopback Mode, this bit controls the state of the modem input RI bit in the MSR register as shown in
Logic 0 = OP1# is HIGH (default).
Logic 1 = OP1# is LOW.
In the Internal Loopback Mode, this bit controls the state of the modem input RI bit in the MSR register as
shown in Figure 11.
MCR[3]: INT Output Enable or OP2# (legacy term)
This bit enables and disables the operation of interrupt output, INT in the Intel mode. If INT output is not used,
OP2# can be used as a general purpose output in the Intel mode. In the Motorola mode, this bit must be set to
logic 0.
Logic 0 = INT output disabled (three state mode) in Intel mode (default).
Logic 1 = INT output enabled (active mode) in Intel mode.
In the Internal Loopback Mode, this bit functions like the OP2# in the 16C550 and is used to set the state of the
modem input CD bit in the MSR register.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 11.
相關PDF資料
PDF描述
XR17C152CM-0A-EVB EVAL BOARD FOR XR17C152 100TQFP
VE-J52-EX CONVERTER MOD DC/DC 15V 75W
SI3056SSI2-EVB BOARD EVAL SI3056/SI3010 SSI
6828281-2 CA 62.5 SC DUP-MTRJ OR SECURE
RHS0E152MCN1GS CAP ALUM 1500UF 2.5V 20% SMD
相關代理商/技術參數
參數描述
XR19L220IL40-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR19L222 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
XR19L222IL64 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
XR19L222IL64-0B-EB 功能描述:界面開發工具 Supports L222 64 pin QFN, pci Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR19L222IL64-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*