REV. 1.0.3 2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO LCR[5]: TX and RX Parity Select If the parity bit is enabled, LCR BIT-5 s" />
參數資料
型號： XR16V554IV80-0A-EB
廠商： Exar Corporation
文件頁數： 18/43頁
文件大小： 0K
描述： EVAL BOARD FOR XR16V554 80LQFP
標準包裝： 1
系列： *
XR16V554/554D
25
REV. 1.0.3
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
LCR[5]: TX and RX Parity Select
If the parity bit is enabled, LCR BIT-5 selects the forced parity format.
LCR BIT-5 = logic 0, parity is not forced (default).
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 0, parity bit is forced to HIGH for the transmit and receive data.
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 1, parity bit is forced to LOW for the transmit and receive data.
TABLE 11: PARITY SELECTION
LCR BIT-5 LCR BIT-4 LCR BIT-3
PARITY SELECTION
X
0
No parity
0
1
Odd parity
0
1
Even parity
1
0
1
Force parity to mark, HIGH
1
Forced parity to space, LOW
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space’, logic 0, state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition. (default)
Logic 1 = Forces the transmitter output (TX) to a “space”, logic 0, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Output
The RTS# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force RTS# output HIGH (default).
Logic 1 = Force RTS# output LOW.
MCR[2]: Reserved
OP1# is not available as an output pin on the V554. But it is available for use during Internal Loopback Mode.
In the Loopback Mode, this bit is used to write the state of the modem RI# interface signal.
相關PDF資料
PDF描述
1-6374614-0 C/A 2.0MM 62.5/125 LC-SC 10M
GBC22DRTN-S734 CONN EDGECARD 44POS DIP .100 SLD
UPM1J820MPD6TD CAP ALUM 82UF 63V 20% RADIAL
RPP30-2424SW-1 CONV DC/DC 30W 9-36VIN 24VOUT
XR16V554IV-0A-EVB EVAL BOARD FOR XR16V554 64LQFP
相關代理商/技術參數
參數描述
XR16V554IV80-F 功能描述:UART 接口集成電路 2.25V-3.6V 16B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V554IV80TR-F 功能描述:UART 接口集成電路 XR16V554IV80TR-F RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V554IV-F 功能描述:通用總線函數 UART RoHS:否 制造商:Texas Instruments 邏輯類型:CMOS 邏輯系列:74VMEH 電路數量:1 開啟電阻（最大值）: 傳播延遲時間:10.1 ns 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大工作溫度:+ 85 C 最小工作溫度:0 C 封裝 / 箱體:TSSOP-48 封裝:Reel
XR16V554IVTR-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V564 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*