參數資料
型號： XR16V2752IL-0B-EB
廠商： Exar Corporation
文件頁數： 9/51頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR V2752 32QFN
標準包裝： 1
系列： *
XR16V2752
17
REV. 1.0.2
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
2.17
Auto Xon/Xoff (Software) Flow Control
When software flow control is enabled (See Table 15), the V2752 compares one or two sequential receive data
characters with the programmed Xon or Xoff-1,2 character value(s). If receive character(s) (RX) match the
programmed values, the V2752 will halt transmission (TX) as soon as the current character has completed
transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the interrupt output
pin will be activated. Following a suspension due to a match of the Xoff character, the V2752 will monitor the
receive data stream for a match to the Xon-1,2 character. If a match is found, the V2752 will resume operation
and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon/Xoff 8-bit flow control registers to 0x00. Following reset the user can
write any Xon/Xoff value desired for software flow control. Different conditions can be set to detect Xon/Xoff
characters (See Table 15) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters are
selected, the V2752 compares two consecutive receive characters with two software flow control 8-bit values
(Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow control
mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the V2752 automatically
sends an Xoff message via the serial TX output to the remote modem. The V2752 sends the Xoff-1,2
characters two-character times (= time taken to send two characters at the programmed baud rate) after the
receive FIFO crosses the programmed trigger level (for all trigger tables). To clear this condition, the V2752 will
transmit the programmed Xon-1,2 characters as soon as receive FIFO is less than one trigger level below the
programmed trigger level (for Trigger Tables A, B, and C) or when receive FIFO is less than the trigger level
minus the hysteresis value (for Trigger Table D). This hysteresis value is the same as the Auto RTS Hysteresis
value in Table 14. Table 6 below explains this when Trigger Table-B (See Table 10) is selected.
* After the trigger level is reached, an xoff character is sent after a short span of time (= time required to send 2
characters); for example, after 2.083ms has elapsed for 9600 baud and 10-bit word length setting.
2.18
Special Character Detect
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data.
The V2752 compares each incoming receive character with Xoff-2 data. If a match exists, the received data will
be transferred to FIFO and ISR bit-4 will be set to indicate detection of special character. Although the Internal
Register Table shows Xon, Xoff Registers with eight bits of character information, the actual number of bits is
dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the number of
character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1 also
determines the number of bits that will be used for the special character comparison. Bit-0 in the Xon, Xoff
Registers corresponds with the LSB bit for the receive character.
TABLE 6: AUTO XON/XOFF (SOFTWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
XOFF CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
XON CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
8
8*
0
16
16*
8
24
24*
16
28
28*
24
相關PDF資料
PDF描述
EEU-FR1J271L CAP ALUM 270UF 63V 20% RADIAL
UPA0J561MPD1TD CAP ALUM 560UF 6.3V 20% RADIAL
H3AKH-3036G IDC CABLE - HSC30H/AE30G/HPK30H
EBM28DTAD-S189 CONN EDGECARD 56POS R/A .156 SLD
MCP1318T-46LE/OT IC SUPERVISOR 4.6V PP/PP SOT23-5
相關代理商/技術參數
參數描述
XR16V2752IL32 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
XR16V2752IL-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V2752ILTR-F 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 2.5V/3.3V 32-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR16V2752ILTR-F
XR16V554 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
XR16V554_07 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*