- 您現在的位置：買賣IC網 > PDF目錄16523 > XR16V2752IL-0B-EB (Exar Corporation)EVAL BOARD FOR V2752 32QFN PDF資料下載
參數資料
| 型號： | XR16V2752IL-0B-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 24/51頁 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR V2752 32QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
XR16V2752
30
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
REV. 1.0.2
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space", LOW state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) to a “space”, LOW, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL, DLM and DLD) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Output
The RTS# pin is a modem control output and may be used for automatic hardware flow control by enabled by
EFR bit-6. The RTS# pin can also be used for Auto RS485 Half-Duplex direction control enabled by FCTR bit-
3. If the modem interface is not used, this output may be used as a general purpose output.
Logic 0 = Force RTS# HIGH (default).
Logic 1 = Force RTS# LOW.
MCR[2]: Reserved
OP1# is not available as an output pin on the V2752. But it is available for use during Internal Loopback Mode.
In the Loopback Mode, this bit is used to write the state of the modem RI# interface signal.
MCR[3]: OP2# Output
OP2# is available as an output pin on the V2752 when AFR[2:1] = ‘00’. In the Loopback Mode, MCR[3] is used
to write the state of the modem CD# interface signal. Also see pin descriptions for MF# pins.
Logic 0 = Forces OP2# output HIGH (default).
Logic 1 = Forces OP2# output LOW.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 12.
MCR[5]: Xon-Any Enable (requires EFR bit-4 = 1)
Logic 0 = Disable Xon-Any function (default).
Logic 1 = Enable Xon-Any function. In this mode, any RX character received will resume transmit operation.
The RX character will be loaded into the RX FIFO, unless the RX character is an Xon or Xoff character and
the V2752 is programmed to use the Xon/Xoff flow control.
相關PDF資料 |
PDF描述 |
|---|---|
| EEU-FR1J271L | CAP ALUM 270UF 63V 20% RADIAL |
| UPA0J561MPD1TD | CAP ALUM 560UF 6.3V 20% RADIAL |
| H3AKH-3036G | IDC CABLE - HSC30H/AE30G/HPK30H |
| EBM28DTAD-S189 | CONN EDGECARD 56POS R/A .156 SLD |
| MCP1318T-46LE/OT | IC SUPERVISOR 4.6V PP/PP SOT23-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V2752IL32 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16V2752IL-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V2752ILTR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 2.5V/3.3V 32-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR16V2752ILTR-F |
| XR16V554 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO |
| XR16V554_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。