- 您現在的位置：買賣IC網 > PDF目錄16526 > XR16M2752IJ-0B-EB (Exar Corporation)EVAL BOARD FOR M2752-B 44PLCC PDF資料下載
參數資料
| 型號： | XR16M2752IJ-0B-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 11/51頁 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR M2752-B 44PLCC |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
XR16M2752
19
REV. 1.0.0
1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
2.19
Sleep Mode with Auto Wake-Up
The M2752 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used.
All of these conditions must be satisfied for the M2752 to enter sleep mode:
■ no interrupts pending for both channels of the M2752 (ISR bit-0 = 1)
■ sleep mode of both channels are enabled (IER bit-4 = 1)
■ modem inputs are not toggling (MSR bits 0-3 = 0)
■ RX input pins are idling HIGH
The M2752 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for
no clock output as an indication that the device has entered the sleep mode.
The M2752 resumes normal operation by any of the following:
■ a receive data start bit transition (HIGH to LOW)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the M2752 is awakened by any one of the above conditions, it will return to the sleep mode automatically
after all interrupting conditions have been serviced and cleared. If the M2752 is awakened by the modem
inputs, a read to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be
entered while an interrupt is pending from channel A or B. The M2752 will stay in the sleep mode of operation
until it is disabled by setting IER bit-4 to a logic 0.
If the address lines, data bus lines, IOW#, IOR#, CSA#, CSB#, and modem input lines remain steady when the
M2752 is in sleep mode, the maximum current will be in the microamp range as specified in the DC Electrical
Characteristics on page 40. If the input lines are floating or are toggling while the M2752 is in sleep mode, the
current can be up to 100 times more. If any of those signals are toggling or floating, then an external buffer
would be required to keep the address, data and control lines steady to achieve the low current. As an
alternative, please refer to the XR16L2751 which is pin-to-pin and software compatible with the M2752 but with
(some additional pins and) the PowerSave feature that eliminates any unnecessary external buffer.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate. Also, it is important to keep
RX A/B inputs idling HIGH or “marking” condition during sleep mode to avoid receiving a “break” condition
upon the restart. This may occur when the external interface transceivers (RS-232, RS-485 or another type)
are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the designer can use a
47k-100k ohm pull-up resistor on the RXA and RXB pins.
相關PDF資料 |
PDF描述 |
|---|---|
| AQ1055N1S-T | INDUCTOR 5.1NH 460MA 0402 SMD |
| VE-J0F-EZ-S | CONVERTER MOD DC/DC 72V 25W |
| 1-5504970-2 | CA 62.5/125UMLDS SC TO SC |
| H8MMH-4036M | DIP CABLE - HDM40H/AE40M/HDM40H |
| VE-JTF-EZ-S | CONVERTER MOD DC/DC 72V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16M2752IJ44 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16M2752IJ44-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M2752IL-0A-EB | 功能描述:界面開發工具 Eval Board for XR16M2752IL-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M2752IL-0B-EB | 功能描述:界面開發工具 Eval Board for XR16M2752IL Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M2752IL32 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。