參數資料
型號： XR16L2750
廠商： Exar Corporation
英文描述： 2.25V TO 5.5V DUART WITH 64-BYTE FIFO
中文描述： 2.25V至5.5V的杜阿爾特64字節FIFO
文件頁數： 17/49頁
文件大?。?/td> 602K
代理商： XR16L2750
XR16L2750
2.25V TO 5.5V DUART WITH 64-BYTE FIFO
REV. 1.0.0
á
17
2.19
The 2750 UART includes the infrared encoder and decoder compatible to the IrDA (Infrared Data Association)
version 1.0. The IrDA 1.0 standard that stipulates the infrared encoder sends out a
3/16 of a bit wide HIGH-
pulse for each “0” bit in the transmit data stream. This signal encoding reduces the on-time of the infrared LED,
hence reduces the power consumption. See
Figure 12
below.
The infrared encoder and decoder are enabled by setting MCR register bit-6 to a ‘1’. When the infrared feature
is enabled, the transmit data output, TX, idles at logic zero level. Likewise, the RX input assumes an idle level
of logic zero from a reset and power up, see
Figure 12
.
Typically, the wireless infrared decoder receives the input pulse from the infrared sensing diode on the RX pin.
Each time it senses a light pulse, it returns a logic 1 to the data bit stream. However, this is not true with some
infrared modules on the market which indicate a logic 0 by a light pulse. So the 2750 has a provision to invert
the input polarity to accommodate this. In this case user can enable FCTR bit-2 to invert the input signal.
Infrared Mode
2.20
The 2750 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used. With EFR bit-4 and IER bit-4 of both channels enabled (set to
a logic 1), the 2750 DUART enters sleep mode when no interrupt is pending for both channels. The 2750 stops
its crystal oscillator to further conserve power in the sleep mode. User can check the XTAL2 pin for no clock
output as an indication that the device has entered the sleep mode. The 2750 resumes normal operation by
any of the following: a receive data start bit transition (logic 1 to 0), a change of logic state on any of the modem
or general purpose input pins: CTS#, DSR#, CD#, RI# or a transmit data byte is loaded to the THR/FIFO by the
user. If the 2750 is awakened by one of the above conditions, it will return to the sleep mode automatically after
all interrupting condition have been serviced and cleared. If the 2750 is awakened by the modem inputs, a read
to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while an
Sleep Mode with Auto Wake-Up
F
IGURE
12. I
NFRARED
T
RANSMIT
D
ATA
E
NCODING
AND
R
ECEIVE
D
ATA
D
ECODING
Character
Data Bits
S
S
0
0
0
0
0
1
1
1
1
1
Bit Time
1/16 Clock Delay
IRdecoder-1
RX Data
Receive
IR Pulse
(RX pin)
Character
Data Bits
S
S
0
0
0
0
0
1
1
1
1
1
TX Data
Transmit
IR Pulse
(TX Pin)
Bit Time
1/2 Bit Time
3/16 Bit Time
IrEncoder-1
相關PDF資料
PDF描述
XR16L2751 2.25V TO 5.5V DUART WITH 64-BYTE FIFO AND POWERSAVE
XR16L2751CM 2.25V TO 5.5V DUART WITH 64-BYTE FIFO AND POWERSAVE
XR16L2751IM 2.25V TO 5.5V DUART WITH 64-BYTE FIFO AND POWERSAVE
XR16L2752 2.25V TO 5.5V DUART WITH 64-BYTE FIFO
XR16L2752CJ 2.25V TO 5.5V DUART WITH 64-BYTE FIFO
相關代理商/技術參數
參數描述
XR16L2750_05 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART WITH 64-BYTE FIFO
XR16L2750CJ 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART WITH 64-BYTE FIFO
XR16L2750CJ-0A-EB 功能描述:UART 接口集成電路 Supports L2750 44 ld PLCC, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2750CJ-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2750CM 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART WITH 64-BYTE FIFO
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*