參數資料
型號： X9520
英文描述： Triple DCP, POR, 2 kbit EEPROM Memory, Dual Voltage Monitors(3個DCP,上電復位,2k位串行EEPROM,分別的雙電壓監控器端電壓-1.0~+15V)
中文描述： 三氯酚，葡萄牙，2千比特EEPROM存儲器，雙電壓監視器（3個副處長，上電復位和2K位串行EEPROM中，分別的雙電壓監控器端電壓-1.0?15V的）
文件頁數： 5/34頁
文件大?。?/td> 210K
代理商： X9520
REV 1.3 4/13/04
Characteristics subject to change without notice.
5 of 34
www.xicor.com
X9520
– Preliminary Information
nate further data transmissions if an ACKNOWLEDGE is
not detected. The master must then issue a STOP condi-
tion to place the device into a known state.
DEVICE INTERNAL ADDRESSING
Addressing Protocol Overview
The user addressable internal components of the X9520
can be split up into three main parts:
—Three Digitally Controlled Potentiometers (DCPs)
—EEPROM array
—Control and Status (CONSTAT) Register
Depending upon the operation to be performed on each
of these individual parts, a 1, 2 or 3 Byte protocol is used.
All operations however must begin with the Slave Address
Byte being issued on the SDA pin. The Slave address
selects the part of the X9520 to be addressed, and speci-
fies if a Read or Write operation is to be performed.
It should be noted that in order to perform a write opera-
tion to either a DCP or the EEPROM array, the Write
Enable Latch (WEL) bit must first be set (See “BL1, BL0:
Block Lock protection bits - (Nonvolatile)” on page 13.)
Slave Address Byte
Following a START condition, the master must output a
Slave Address Byte (Refer to Figure 4.). This byte con-
sists of three parts:
—The Device Type Identifier which consists of the most
significant four bits of the Slave Address (SA7 - SA4).
The Device Type Identifier must always be set to 1010
in order to select the X9520.
—The next three bits (SA3 - SA1) are the Internal Device
Address bits. Setting these bits to 000 internally selects
the EEPROM array, while setting these bits to 111
selects the DCP structures in the X9520. The CON-
STAT Register may be selected using the Internal
Device Address 010.
—The Least Significant Bit of the Slave Address (SA0)
Byte is the R/W bit. This bit defines the operation to be
performed on the device being addressed (as defined
in the bits SA3 - SA1). When the R/W bit is “1”, then a
READ operation is selected. A “0” selects a WRITE
operation (Refer to Figure 4.)
Data Output
from
Transmitter
Data Output
from
Receiver
8
1
9
Start
Acknowledge
Figure 3.
Acknowledge Response From Receiver
SCL
from
Master
SA6
SA7
SA5
SA3
SA2
SA1
SA0
DEVICE TYPE
IDENTIFIER
READ /
WRITE
SA4
Internal Address
(SA3 - SA1)
000
010
111
Internally Addressed
Device
EEPROM Array
CONSTAT Register
DCP
Bit SA0
Operation
0
WRITE
1
READ
R/W
Figure 4.
Slave Address Format
1 0 1
0
ADDRESS
INTERNAL
DEVICE
相關PDF資料
PDF描述
X9521 Dual DCP, EEPROM Memory
X9521 Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules
X9521V20I Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules
X95820 Dual Digitally Controlled Potentiometers (XDCP)(雙數控電位器)
X95840 Quad Digital Controlled Potentiometers (XDCP)(四數控電位器（XDCP）)
相關代理商/技術參數
參數描述
X9520_06 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple DCP, POR, 2kbit EEPROM Memory, Dual Voltage Monitors
X9520_07 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple DCP, POR, 2kbit EEPROM Memory, Dual Voltage Monitors
X9520B20IA 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors
X9520B20I-A 功能描述:IC LASR CTRLR 3CHAN 5.5V 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝
X9520B20I-AT1 功能描述:IC LASR CTRLR 3CHAN 5.5V 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*