參數資料
型號： W987Z6CBG80
廠商： WINBOND ELECTRONICS CORP
元件分類： DRAM
英文描述： 8M X 16 SYNCHRONOUS DRAM, 6 ns, PBGA54
封裝： 8 X 9 MM, 1.20 MM HEIGHT, FBGA-54
文件頁數： 5/46頁
文件大?。?/td> 1634K
代理商： W987Z6CBG80
Preliminary W987Z6CB
Publication Release Date: June 24, 2002
- 13 -
Revision A1
Write with Auto Precharge command
( RAS ="H", CAS = "L", WE = "L", BS0, BS1 = Bank, A10 = "H", A0 to A8 = Column Address)
The Write with Auto Precharge command performs the Precharge operation automatically after
the Write operation. This command must not be interrupted by any other commands.
Read command
( RAS ="H", CAS = "L", WE = "H", BS0, BS1 = Bank, A10 = "L", A0 to A8 = Column Address)
The Read command performs a Read operation to the bank designated by BS. The length of read
data (Burst Length), Addressing Mode and CAS Latency (access time from CAS command in a
clock cycle) must be programmed in the Mode Register at power-up prior to the Read operation.
Read with Auto Precharge command
( RAS ="H", CAS = "L", WE = "H", BS0, BS1 = Bank, A10 = "H", A0 to A8 = Column Address)
The Read with Auto precharge command automatically performs the Precharge operation after
the Read operation. This command must not be interrupted by any other command.
Mode Register Set command
( RAS = "L", CAS = "L", WE = "L", BS0 = "L", BS1 = "L", A0 to A11 = Register Data)
The Mode Register Set command programs the values of Burst Length, Addressing Mode, CAS
latency and Write Mode in the Mode Register. The default values in the Mode Register after
power-up are undefined, therefore this command must be issued during the power-up sequence.
Also, this command can be issued while all banks are in the idle state. Refer to the table for
specific codes.
Extended Mode Register Set command
( RAS = "L", CAS = "L", WE = "L", BS0 = "L", BS1 = "H", A0 to A11 = Register data)
The Extended Mode Register Set command programs the values of Driver Strength, Temperature
Compensated Self Refresh and Partial Array Self Refresh. The default value of the extended
mode register is Full Driver Strength, 70 degrees C and All banks Refreshed
No-Operation command
( RAS = "H", CAS = "H", WE = "H")
The No-Operation command simply performs no operation (same command as Device Deselect).
Burst Read stop command
( RAS = "H", CAS = "H", WE = "L")
The Burst stop command is used to stop the burst operation. This command is only valid during a
Burst Read operation.
相關PDF資料
PDF描述
WA-1RVX051-A4 SNAP ACTING/LIMIT SWITCH
WA-1RX12-A4 SNAP ACTING/LIMIT SWITCH
WB3M200VD1R800 200 CONTACT(S), MALE, STRAIGHT SINGLE PART CARD EDGE CONN, SURFACE MOUNT, PLUG
WB3F200VD1R1000 200 CONTACT(S), FEMALE, STRAIGHT SINGLE PART CARD EDGE CONN, SURFACE MOUNT, RECEPTACLE
WB3F200VD1 200 CONTACT(S), FEMALE, STRAIGHT SINGLE PART CARD EDGE CONN, SURFACE MOUNT, RECEPTACLE
相關代理商/技術參數
參數描述
W987Z6CBN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DRAM
W988D2FB 制造商:WINBOND 制造商全稱:Winbond 功能描述:256Mb Mobile LPSDR
W988D2FBJX6E 制造商:Winbond Electronics Corp 功能描述:IC LPSDR SDRAM 256MBIT 90VFBGA
W988D2FBJX6I 制造商:WINBOND 制造商全稱:Winbond 功能描述:256Mb Mobile LPSDR
W988D2FBJX7E 制造商:Winbond Electronics Corp 功能描述:IC LPSDR SDRAM 256MBIT 90VFBGA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*