- 您現在的位置：買賣IC網 > PDF目錄361795 > W83977CTF-PW PERIPHERAL (MULTIFUNCTION) CONTROLLER PDF資料下載
參數資料
| 型號： | W83977CTF-PW |
| 英文描述： | PERIPHERAL (MULTIFUNCTION) CONTROLLER |
| 中文描述： | 周邊（多功能）控制器 |
| 文件頁數： | 85/161頁 |
| 文件大?。?/td> | 592K |
| 代理商： | W83977CTF-PW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁
W83977EF/ CTF
PRELIMINARY
Publication Release Date: March 1999
-76 -
Revision A1
5.3.13 ECP Operation
The host must negotiate on the parallel port to determine if the peripheral supports the ECP protocol
before ECP operation. After negotiation, it is necessary to initialize some of the port bits. The
following are required:
(a) Set direction = 0, enabling the drivers.
(b) Set strobe = 0, causing the nStrobe signal to default to the deasserted state.
(c) Set autoFd = 0, causing the nAutoFd signal to default to the deasserted state.
(d) Set mode = 011 (ECP Mode)
ECP address/RLE bytes or data bytes may be sent automatically by writing the ecpAFifo or ecpDFifo,
respectively.
5.3.13.1 Mode Switching
Software will execute P1284 negotiation and all operations prior to a data transfer phase under
programmed I/O control (mode 000 or 001). Hardware provides an automatic control line handshake,
moving data between the FIFO and the ECP port only in the data transfer phase (mode 011 or 010).
If the port is in mode 000 or 001 it may switch to any other mode. If the port is not in mode 000 or 001
it can only be switched into mode 000 or 001. The direction can be changed only in mode 001.
When in extended forward mode, the software should wait for the FIFO to be empty before switching
back to mode 000 or 001. In ECP reverse mode the software waits for all the data to be read from the
FIFO before changing back to mode 000 or 001.
5.3.13.2 Command/Data
ECP mode allows the transfer of normal 8-bit data or 8-bit commands. In the forward direction,
normal data are transferred when HostAck is high and an 8-bit command is transferred when HostAck
is low. The most significant bits of the command indicate whether it is a run-length count (for
compression) or a channel address.
In the reverse direction, normal data are transferred when PeriphAck is high and an 8-bit command is
transferred when PeriphAck is low. The most significant bit of the command is always zero.
5.3.13.3 Data Compression
The W83977EF/CTF supports run length encoded (RLE) decompression in hardware and can transfer
compressed data to a peripheral. Note that the odd (RLE) compression in hardware is not supported.
In order to transfer data in ECP mode, the compression count is written to the ecpAFifo and the data
byte is written to the ecpDFifo.
5.3.14 FIFO Operation
The FIFO threshold is set in configuration register 5. All data transfers to or from the parallel port can
proceed in DMA or Programmed I/O (non-DMA) mode, as indicated by the selected mode. The FIFO
is used by selecting the Parallel Port FIFO mode or ECP Parallel Port Mode. After a reset, the FIFO
is disabled.
相關PDF資料 |
PDF描述 |
|---|---|
| W83977TF(EOL) | W83877TF plus KBC. CIR. RTC |
| W83C42 | KEYBOARD CONTROLLER |
| W83C42P | KEYBOARD CONTROLLER |
| W83C45 | Keyboard Controller |
| W83C45P | Keyboard Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W83977EF | 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND ISA I/O |
| W83977EF-AW | 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND ISA I/O |
| W83977EF-PW | 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O |
| W83977EG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND ISA I/O |
| W83977EG-AW | 功能描述:IC I/O CONTROLLER 128-PQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
發布緊急采購，3分鐘左右您將得到回復。