參數資料
型號： W25X40BLSNIG
廠商： WINBOND ELECTRONICS CORP
元件分類： PROM
英文描述： 4M X 1 FLASH 2.7V PROM, PDSO8
封裝： 0.150 INCH, GREEN, PLASTIC, SOIC-8
文件頁數： 11/53頁
文件大?。?/td> 2041K
代理商： W25X40BLSNIG
W25X10BL/20BL/40BL
Publication Release Date: October 14, 2009
- 19 -
Preliminary -- Revision A
9.2.7
Write Status Register (01h)
The Write Status Register instruction allows the Status Register to be written. Only non-volatile Status
Register bits SRP, TB, BP2, BP1, BP0 (bits 7 thru 2 of Status Register) can be written to. All other
Status Register bit locations are read-only and will not be affected by the Write Status Register
instruction. The Status Register bits are shown in figure 3 and described in 9.1.
To write non-volatile Status Register bits, a standard Write Enable (06h) instruction must previously
have been executed for the device to accept the Write Status Register Instruction (Status Register bit
WEL must equal 1). Once write enabled, the instruction is entered by driving /CS low, sending the
instruction code “01h”, and then writing the status register data byte as illustrated in figure 8.
To write volatile Status Register bits, a Write Enable for Volatile Status Register (50h) instruction must
have been executed prior to the Write Status Register instruction (Status Register bit WEL remains 0).
Upon power off, the volatile Status Register bit values will be lost, and the non-volatile Status Register
bit values will be restored when power on again.
To complete the Write Status Register instruction, the /CS pin must be driven high after the eighth bit
of data that is clocked in. If this is not done the Write Status Register instruction will not be executed.
During non-volatile Status Register write operation (06h combined with 01h), after /CS is driven high,
the self-timed Write Status Register cycle will commence for a time duration of tW (See AC
Characteristics). While the Write Status Register cycle is in progress, the Read Status Register
instruction may still be accessed to check the status of the BUSY bit. The BUSY bit is a 1 during the
Write Status Register cycle and a 0 when the cycle is finished and ready to accept other instructions
again. After the Write Status Register cycle has finished, the Write Enable Latch (WEL) bit in the
Status Register will be cleared to 0.
During volatile Status Register write operation (50h combined with 01h), after /CS is driven high, the
Status Register bits will be refreshed to the new values within the time period of tSHSL2 (See AC
Characteristics). BUSY bit will remain 0 during the Status Register bit refresh period.
Please refer to 9.1 for detailed Status Register Bit descriptions. Factory default for all status Register
bits are 0.
.
相關PDF資料
PDF描述
W3H128M72ER-667SBC 128M X 72 DDR DRAM, 0.5 ns, PBGA255
W3H128M72ER-667SBM 128M X 72 DDR DRAM, 0.5 ns, PBGA255
W3EG72126S262AJD3SG 128M X 72 DDR DRAM MODULE, 0.75 ns, DMA184
W3EG72126S265JD3SG 128M X 72 DDR DRAM MODULE, 0.75 ns, DMA184
W3H128M72E0533SBM DDR DRAM, PBGA208
相關代理商/技術參數
參數描述
W25X40BLSSIG 制造商:WINBOND 制造商全稱:Winbond 功能描述:1M-BIT, 2M-BIT AND 4M-BIT 2.5V SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL I/O SPI
W25X40BLSVIG 制造商:WINBOND 制造商全稱:Winbond 功能描述:2.5V 4M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL I/O SPI
W25X40BLUXIG 制造商:WINBOND 制造商全稱:Winbond 功能描述:2.5V 4M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL I/O SPI
W25X40BLZPIG 制造商:WINBOND 制造商全稱:Winbond 功能描述:1M-BIT, 2M-BIT AND 4M-BIT 2.5V SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL I/O SPI
W25X40BV 制造商:WINBOND 制造商全稱:Winbond 功能描述:1M-BIT, 2M-BIT AND 4M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL I/O SPI
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*