參數資料
型號： W25X10BVSNIG
廠商： WINBOND ELECTRONICS CORP
元件分類： PROM
英文描述： 1M X 1 FLASH 2.7V PROM, PDSO8
封裝： 0.150 INCH, GREEN, PLASTIC, SOIC-8
文件頁數： 2/51頁
文件大小： 1632K
代理商： W25X10BVSNIG
W25X10BV/20BV/40BV
- 10 -
8.2
WRITE PROTECTION
Applications that use non-volatile memory must take into consideration the possibility of noise and
other adverse system conditions that may compromise data integrity. To address this concern the
W25X10BV/20BV/40BV provides several means to protect data from inadvertent writes.
8.2.1
Write Protect Features
Device resets when VCC is below threshold.
Time delay write disable after Power-up.
Write enable/disable instructions.
Automatic write disable after program and erase.
Software write protection using Status Register.
Hardware write protection using Status Register and /WP pin.
Write Protection using Power-down instruction.
Upon power-up or at power-down the W25X10BV/20BV/40BV will maintain a reset condition while
VCC is below the threshold value of VWI, (See Power-up Timing and Voltage Levels and Figure 25).
While reset, all operations are disabled and no instructions are recognized. During power-up and after
the VCC voltage exceeds VWI, all program and erase related instructions are further disabled for a
time delay of tPUW. This includes the Write Enable, Page Program, Sector Erase, Block Erase, Chip
Erase and the Write Status Register instructions. Note that the chip select pin (/CS) must track the
VCC supply level at power-up until the VCC-min level and tVSL time delay is reached. If needed a pull-
up resister on /CS can be used to accomplish this.
After power-up the device is automatically placed in a write-disabled state with the Status Register
Write Enable Latch (WEL) set to a 0. A Write Enable instruction must be issued before a Page
Program, Sector Erase, Chip Erase or Write Status Register instruction will be accepted. After
completing a program, erase or write instruction the Write Enable Latch (WEL) is automatically
cleared to a write-disabled state of 0.
Software controlled write protection is facilitated using the Write Status Register instruction and setting
the Status Register Protect (SRP) and Block Protect (TB, BP2, BP1, and BP0) bits. These Status
Register bits allow a portion or all of the memory to be configured as read only. Used in conjunction
with the Write Protect (/WP) pin, changes to the Status Register can be enabled or disabled under
hardware control. See Status Register for further information.
Additionally, the Power-down instruction offers an extra level of write protection as all instructions are
ignored except for the Release Power-down instruction.
相關PDF資料
PDF描述
W3EG6467S403D4SG 64M X 64 DDR DRAM MODULE, 0.7 ns, DMA200
W7NCF02GH10CSAEG 128M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC
W7NCF04GH10CSAADM1G FLASH 3.3V PROM MODULE, XMA50
W7NCF04GH10ISA3FM1G FLASH 3.3V PROM MODULE, XMA50
W7NCF04GH10ISA9HM1G FLASH 3.3V PROM MODULE, XMA50
相關代理商/技術參數
參數描述
W25X10BVZPIG 功能描述:IC SPI FLASH 1MBIT 8WSON RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:1,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 線串口 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.173"，4.40mm 寬） 供應商設備封裝:8-MFP 包裝:帶卷 (TR)
W25X10CLSNIG 制造商:Winbond Electronics Corp 功能描述:Flash Serial-SPI 2.5V/3.3V 1Mbit 128K/64K x 8bit/16bit 8ns 8-Pin SOIC 制造商:Winbond Electronics Corp 功能描述:IC FLASH 1MBIT 104MHZ 8SOIC
W25X10CLSNIG TR 制造商:Winbond Electronics Corp 功能描述:SPIFLASH, 1M-BIT, 4KB UNIFORM 制造商:Winbond Electronics Corp 功能描述:IC MEMORY
W25X10CLZPIG 制造商:Winbond Electronics Corp 功能描述:IC FLASH 1MBIT 104MHZ 8WSON
W25X10CLZPIG TR 制造商:Winbond Electronics Corp 功能描述:IC FLASH 1MBIT 104MHZ 8WSON
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*