- 您現在的位置：買賣IC網 > PDF目錄140358 > W25X10BVSNIG (WINBOND ELECTRONICS CORP) 1M X 1 FLASH 2.7V PROM, PDSO8 PDF資料下載
參數資料
| 型號： | W25X10BVSNIG |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 1M X 1 FLASH 2.7V PROM, PDSO8 |
| 封裝： | 0.150 INCH, GREEN, PLASTIC, SOIC-8 |
| 文件頁數： | 17/51頁 |
| 文件大?。?/td> | 1632K |
| 代理商： | W25X10BVSNIG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
W25X10BV/20BV/40BV
- 24 -
9.2.11
Continuous Read Mode Bits (M7-0)
The “Continuous Read Mode” bits are used in conjunction with the “Fast Read Dual I/O” instruction to
provide the highest random Flash memory access rate with minimum SPI instruction overhead, thus
allow true XIP (execute in place) to be performed on serial flash devices.
M7-0 need to be set by the Dual I/O Read instruction. M5-4 are used to control whether the 8-bit SPI
instruction code BBh is needed or not for the next command. When M5-4 = (1,0), the next command
will be treated same as the current Dual I/O Read command without needing the 8-bit instruction
code; when M5-4 do not equal to (1,0), the device returns to normal SPI mode, all commands can be
accepted. M7-6 and M3-0 are reserved bits for future use, either 0 or 1 values can be used.
9.2.12
Continuous Read Mode Reset (FFFFh)
Continuous Read Mode Reset instruction can be used to set M4 = 1, thus the device will release the
Continuous Read Mode and return to normal SPI operation, as shown in figure 12.
1
02
/CS
Mode 0
Mode 3
46
810
12
Mode 0
Mode 3
CLK
IO0
IO
Mode Bit Reset
for Dual I/O
Don’t Care
FFFFh
/CS
Mode 0
Mode 3
CLK
IO0
IO
Don’t Care
13
57
911
13
14
15
Figure 12. Continuous Read Mode Reset for Fast Read Dual I/O
Since W25X10BV/20BV/40BV does not have a hardware Reset pin, so if the controller resets while
W25X10BV/20BV/40BV are set to Continuous Mode Read, the W25X10BV/20BV/40BV will
not recognize any initial standard SPI instructions from the controller. To address this possibility, it is
recommended to issue a Continuous Read Mode Reset instruction as the first instruction after a
system Reset. Doing so will release the device from the Continuous Read Mode and allow Standard
SPI instructions to be recognized.
To reset “Continuous Read Mode” during Dual I/O operation, sixteen clocks are needed to shift in
instruction “FFFFh”.
相關PDF資料 |
PDF描述 |
|---|---|
| W3EG6467S403D4SG | 64M X 64 DDR DRAM MODULE, 0.7 ns, DMA200 |
| W7NCF02GH10CSAEG | 128M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC |
| W7NCF04GH10CSAADM1G | FLASH 3.3V PROM MODULE, XMA50 |
| W7NCF04GH10ISA3FM1G | FLASH 3.3V PROM MODULE, XMA50 |
| W7NCF04GH10ISA9HM1G | FLASH 3.3V PROM MODULE, XMA50 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W25X10BVZPIG | 功能描述:IC SPI FLASH 1MBIT 8WSON RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:1,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 線串口 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.173"，4.40mm 寬） 供應商設備封裝:8-MFP 包裝:帶卷 (TR) |
| W25X10CLSNIG | 制造商:Winbond Electronics Corp 功能描述:Flash Serial-SPI 2.5V/3.3V 1Mbit 128K/64K x 8bit/16bit 8ns 8-Pin SOIC 制造商:Winbond Electronics Corp 功能描述:IC FLASH 1MBIT 104MHZ 8SOIC |
| W25X10CLSNIG TR | 制造商:Winbond Electronics Corp 功能描述:SPIFLASH, 1M-BIT, 4KB UNIFORM 制造商:Winbond Electronics Corp 功能描述:IC MEMORY |
| W25X10CLZPIG | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 1MBIT 104MHZ 8WSON |
| W25X10CLZPIG TR | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 1MBIT 104MHZ 8WSON |
發布緊急采購，3分鐘左右您將得到回復。