- 您現在的位置：買賣IC網 > PDF目錄382726 > UT80C196KD-WCA MICROCONTROLLER|16-BIT|8096 CPU|CMOS|QFL|68PIN|PLASTIC PDF資料下載
參數資料
| 型號： | UT80C196KD-WCA |
| 英文描述： | MICROCONTROLLER|16-BIT|8096 CPU|CMOS|QFL|68PIN|PLASTIC |
| 中文描述： | 單片機| 16位| 8096的CPU |的CMOS | QFL | 68PIN |塑料 |
| 文件頁數： | 16/42頁 |
| 文件大?。?/td> | 190K |
| 代理商： | UT80C196KD-WCA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
16
19
TUQ
P1.0
---
Port 1 Pin 0. A quasi-bidirectional port pin that is read and writ-
ten at location 0Fh of HWindow 0.
20
TUQ
P1.1
---
Port 1 Pin 1. A quasi-bidirectional port pin that is read and writ-
ten at location 0Fh of HWindow 0.
21
TUQ
P1.2
---
Port 1 Pin 2. A quasi-bidirectional port pin that is read and writ-
ten at location 0Fh of HWindow 0.
22
TUQ
P1.3
---
Port 1 Pin 3. A quasi-bidirectional port pin that is read and writ-
ten at location 0Fh of HWindow 0.
Setting IOC3.2 = 0 enables the P1.3 function of pin 22.
TUO
PWM1
---
Pulse Width Modulator (PWM) Output 1. The output signal
will be a waveform whose duty cycle is programmed by the
PWM1_CONTROL register, and the frequency is selected by
IOC2.2.
Setting IOC3.2 = 1 enables the PWM1 function of pin 22.
23
TUQ
P1.4
---
Port 1 Pin 4. A quasi-bidirectional port pin that is read and writ-
ten at location 0Fh of HWindow 0.
Setting IOC3.3 = 0 enables the P1.4 function of pin 23.
TUO
PWM2
---
Pulse Width Modulator (PWM) Output 2. The output signal
will be a waveform whose duty cycle is programmed by the
PWM2_CONTROL register, and the frequency is selected by
IOC2.2.
Setting IOC3.3 = 1 enables the PWM2 function of pin 23.
24
TI
HSI.0
---
High Speed Input Module, input pin 0. Unless masked, a rising
edge on this input will generate the HSI.0 Pin interrupt (INT04,
2008h). Assert the HSI.0 pin for at least 2 state times to ensure
acknowledgment by the interrupt controller.
Setting IOC0.0 = 1 enables pin 24 as an HSI input, and allows
events on this pin to be loaded into the HSI FIFO.
TI
T2RST
High
Timer 2 Reset. A rising edge on the T2RST pin resets Timer 2.
To enable the T2RST function of pin 24, set IOC0.3 = 1 and
IOC0.5 = 1.
Table 10: 68-lead Flat Pack Pin Descriptions
QFP Pin#
I/O
Name
Active
Description
相關PDF資料 |
PDF描述 |
|---|---|
| UT80C196KD-WCC | MICROCONTROLLER|16-BIT|8096 CPU|CMOS|QFL|68PIN|PLASTIC |
| UTC79L05 | VOLTAGE REGULATOR(66.37 k ) |
| UTC79L12 | VOLTAGE REGULATOR(66.37 k ) |
| UTCACB | Voltage-Controlled Oscillator |
| UTCALB | Voltage-Controlled Oscillator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UT80C196KD-WCC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|16-BIT|8096 CPU|CMOS|QFL|68PIN|PLASTIC |
| UT80CRH196KD | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:20MHz 16-bit Microcontroller |
| UT80CRH196KD-WCA | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:20MHz 16-bit Microcontroller |
| UT80CRH196KD-WCC | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:20MHz 16-bit Microcontroller |
| UT80CRH196KD-WCX | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:20MHz 16-bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。