參數資料
型號： UCB1100LP
廠商： NXP Semiconductors N.V.
英文描述： Advanced modem/audio analog front-end
中文描述： 先進的調制解調器/音頻模擬前端
文件頁數： 16/36頁
文件大?。?/td> 290K
代理商： UCB1100LP
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
16
6.3
The UCB1100 contains an on chip interface for a 4 wire resistive
touch screen. This interface supports three modes of touch screen
measurements, position, pressure and plate resistance.
Touch Screen Measurement Modes
6.3.1
Two position measurements are needed to determine the location of
the pressed spot. First an X measurement, secondly a Y
measurement. The X plate is biased during the X position
measurement the X plate and the voltage on one or both Y terminals
(tspy, tsmy) measured. The circuit can been represented by a
potentiometer, with the tspy and/or tsmy electrode being the ‘wiper’.
The measured voltage on the tspy/tsmy terminal is proportional to
the X position of the pressed spot of the touch screen.
Position Measurement
In the Y position mode the X plate and Y plate terminals are
interchanged, thus the Y plate is biased on the voltage on the tspx
and/or tsmx terminal is measured.
Vtscbias
Vposition
tsmy
tspy
tsmx
SN00139
Figure 14.
Touch Screen Setup for Position Measurement
6.3.2
The pressure used to press the touch screen can be determined. In
fact the contact resistance between the X and Y plate is measured,
which is a good indication of the size of the pressed spot and the
applied pressure. A soft stylus, e.g. a finger, leads to a rather large
contact area between the two plates when a large pressure is
applied. A hard stylus, e.g. a pen, leads to less variation in
measured contact resistance since the contact area is rather small.
Pressure Measurement
One plate is biased at one or both terminals during this pressure
measurement, whereas the other plate is grounded, again on one or
both terminals. The current flowing through the touch screen is a
direct indication for the resistance between both plates. A
compensation for the series resistance, formed by the touch screen
plates itself will improve the accuracy of this measurement.
tspy
Vtscbiasipresure
SN00140
Figure 15.
Touch Screen Setup for Pressure Measurement
6.3.3
The plate resistance of a touch screen varies typically a lot due to
processing spreads. Knowing the actual plate resistance makes it
possible to compensate for the plate resistance effects in the
pressure resistance measurements. Secondly the plate resistance
decreases when two or more spots on the touch screen are
pressed. In that case a part of one plate, e.g. the X plate is shorted
by the other plate, which decreases the actual plate resistance.
Plate Resistance Measurement
The plate resistance measurement is executed in the same way as
the pressure resistance measurement. In this case only one of the
two plates is biased and the other plate is kept floating. The current
through the connected plate is again a direct indication of the
connected resistance.
Xplate
tsmy
tspx
Vtscbias
iplate
SN00141
Figure 16.
Touch Screen Setup for Plate Resistance
Measurement
相關PDF資料
PDF描述
UCB1200 Advanced modem/audio analog front-end
UCB1200BE Advanced modem/audio analog front-end
UCB1300 Advanced modem/audio analog front-end
UCB1300BE Advanced modem/audio analog front-end
UCB1400BE Audio codec with touch screen controller and power management monitor
相關代理商/技術參數
參數描述
UCB1100LP/X3 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced modem/audio analog front-end
UCB-12 功能描述:斷路器 CIRCUIT BREAKER RoHS:否 制造商:Phoenix Contact 產品:Device Circuit Breakers 產品類型:Thermomagnetic 電流額定值:2 A 電壓額定值 AC:240 V, 277 V 電壓額定值 DC:50 V 極數:1 Pole 執行器類型:Slide 電路功能:Trip Free 系列:CB TM1 工作溫度范圍:- 30 C to + 60 C 照明:No
UCB1200 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced modem/audio analog front-end
UCB1200B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UCB1200B
UCB1200BE 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced modem/audio analog front-end
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*