- 您現在的位置：買賣IC網 > PDF目錄382720 > UCB1100 (NXP Semiconductors N.V.) Advanced modem/audio analog front-end PDF資料下載
參數資料
| 型號： | UCB1100 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Advanced modem/audio analog front-end |
| 中文描述： | 先進的調制解調器/音頻模擬前端 |
| 文件頁數： | 9/36頁 |
| 文件大?。?/td> | 290K |
| 代理商： | UCB1100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
9
micp
micgnd
vssa1
vdda1
micp
micgnd
vssa1
vdda1
UCB1100
UCB1100
‘Passive’ Microphone
‘Active’ Microphone
SN00129
Figure 4.
Possible Microphone Connections
The UCB1100 audio codec input path accepts microphone signals
directly, only a DC blocking capacitor is needed, since the micp input
is biased around 1.4V. The ‘ground’ side of the microphone is either
connected to the analogue ground (vssa1) or to the micgnd pin of
the UCB1100. The latter will decrease the current consumption of
active microphones, since the micgnd pin is made Hi-Z when the
audio codec input path is disabled.
The full scale input voltage of the audio input path is programmable
in 1.5dB steps by setting the appropriate data in the audio-input-gain
bits in the audio control register A.
A clip detection circuit will inform the user whenever the input
voltage exceeds the maximum input voltage. In that case the clip
detect statusbit in audio control register B is set. An interrupt is
generated on the irqout pin of the UCB1100 whenever the enable
audioclip detect rising interrupt or the enable audio detect falling
edge interrupt bit is set in the rising edge interrupt enable or falling
edge interrupt control register B is set.
a
d
0dB
24dB
48dB
0dB
21dB
24dB
48dB
69dB
programmed attenuation
SN00130
Figure 5.
Analogue and Digital Attenuation Settings
Audio Output Path
The output level can be attenuated in 3dB steps down to -69dB. The
8 highest attenuation steps are implemented in the analogue
circuitry, while the two 24dB steps are implemented in the digital
domain. This preserves the ‘audio quality’ of the output signal at
lowest attenuation settings. The speaker driver is muted when the
audio-mutebit in the audio control register B is set. The speaker
driver will remain activated in that case, however no signal is
produced by the speaker driver circuitry.
UCB1100
UCB1100
UCB1100
spkrp
spkrn
spkrp
spkrp
spkrn
spkrn
Bridge Tied
Speaker
Load
Single Ended Speaker Connections
SN00131
Figure 6.
Possible Speaker Connections
The speaker driver is designed to directly drive a bridge tied load
(BTL). This yields the highest output power and it does not require
external DC blocking capacitors. The speaker driver also accepts
single ended connection of a speaker, in which case the maximum
output power is reduced to a quarter of the BTL situation.
Consequently this way of connecting the speaker to the speaker
driver reduces the power consumption of the speaker driver in the
UCB1100 by a factor of 2. Figure 6 shows possible ways to connect
a speaker to the UCB1100.
The audio input and output path are activated independently; the
input path is enabled when the audio-input-enablebit is set, the
output path is enabled when the audio-output-enablebit is set in the
audio control register B. This provides the user the means to reduce
the current consumption of the UCB1100 if one part of the audio
codec is not used in the application.
The audio codec has a loopback mode for system test purposes,
which is activated when the audio_loopback enablebit in the audio
control register B is set. This is an analogue loopback which
internally connects the output of the audio output path to the input of
the audio input path, (see Figure 3). In this mode the normal
microphone input is ignored, but the speaker driver can be operated
normally.
相關PDF資料 |
PDF描述 |
|---|---|
| UCB1100LP | Advanced modem/audio analog front-end |
| UCB1200 | Advanced modem/audio analog front-end |
| UCB1200BE | Advanced modem/audio analog front-end |
| UCB1300 | Advanced modem/audio analog front-end |
| UCB1300BE | Advanced modem/audio analog front-end |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCB1100LP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced modem/audio analog front-end |
| UCB1100LP/X3 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced modem/audio analog front-end |
| UCB-12 | 功能描述:斷路器 CIRCUIT BREAKER RoHS:否 制造商:Phoenix Contact 產品:Device Circuit Breakers 產品類型:Thermomagnetic 電流額定值:2 A 電壓額定值 AC:240 V, 277 V 電壓額定值 DC:50 V 極數:1 Pole 執(zhí)行器類型:Slide 電路功能:Trip Free 系列:CB TM1 工作溫度范圍:- 30 C to + 60 C 照明:No |
| UCB1200 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced modem/audio analog front-end |
| UCB1200B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UCB1200B |
發(fā)布緊急采購，3分鐘左右您將得到回復。