- 您現在的位置：買賣IC網 > PDF目錄380958 > UC3842BVD1R2 I2C BUS-CONTROLLED MULTISTANDARD SINGLE CHIP TV PROCESSOR PDF資料下載
參數資料
| 型號： | UC3842BVD1R2 |
| 英文描述： | I2C BUS-CONTROLLED MULTISTANDARD SINGLE CHIP TV PROCESSOR |
| 中文描述： | 模擬IC |
| 文件頁數： | 10/20頁 |
| 文件大小： | 296K |
| 代理商： | UC3842BVD1R2 |
UC3842B, UC3843B, UC2842B, UC2843B, NCV3843BV
http://onsemi.com
10
Undervoltage Lockout
Two undervoltage lockout comparators have been
incorporated to guarantee that the IC is fully functional
before the output stage is enabled. The positive power
supply terminal (V
CC
) and the reference output (V
ref
) are
each monitored by separate comparators. Each has built–in
hysteresis to prevent erratic output behavior as their
respective thresholds are crossed. The V
CC
comparator
upper and lower thresholds are 16 V/10 V for the UCX842B,
and 8.4 V/7.6 V for the UCX843B. The V
ref
comparator
upper and lower thresholds are 3.6 V/3.4 V. The large
hysteresis and low startup current of the UCX842B makes
it ideally suited in off–line converter applications where
efficient bootstrap startup techniques are required
(Figure 34). The UCX843B is intended for lower voltage
dc–to–dc converter applications. A 36 V zener is connected
as a shunt regulator from V
CC
to ground. Its purpose is to
protect the IC from excessive voltage that can occur during
system startup. The minimum operating voltage (V
CC
) for
the UCX842B is 11 V and 8.2 V for the UCX843B.
These devices contain a single totem pole output stage that
was specifically designed for direct drive of power
MOSFETs. It is capable of up to
±
1.0 A peak drive current
and has a typical rise and fall time of 50 ns with a 1.0 nF load.
Additional internal circuitry has been added to keep the
Output in a sinking mode whenever an undervoltage lockout
is active. This characteristic eliminates the need for an
external pull–down resistor.
The SO–14 surface mount package provides separate pins
for V
C
(output supply) and Power Ground. Proper
implementation will significantly reduce the level of
switching transient noise imposed on the control circuitry.
This becomes particularly useful when reducing the I
pk(max)
clamp level. The separate V
C
supply input allows the
designer added flexibility in tailoring the drive voltage
independent of V
CC
. A zener clamp is typically connected
to this input when driving power MOSFETs in systems
where V
CC
is greater than 20 V. Figure 26 shows proper
power and control ground connections in a current–sensing
power MOSFET application.
Reference
The 5.0 V bandgap reference is trimmed to
±
1.0%
tolerance at T
J
= 25
°
C on the UC284XB, and
±
2.0% on the
UC384XB. Its primary purpose is to supply charging current
to the oscillator timing capacitor. The reference has short–
circuit protection and is capable of providing in excess of
20 mA for powering additional control system circuitry.
Design Considerations
Do not attempt to construct the converter on
wire–wrap or plug–in prototype boards.
High frequency
circuit layout techniques are imperative to prevent
pulse–width jitter. This is usually caused by excessive noise
pick–up imposed on the Current Sense or Voltage Feedback
inputs. Noise immunity can be improved by lowering circuit
impedances at these points. The printed circuit layout should
contain a ground plane with low–current signal and
high–current switch and output grounds returning on
separate paths back to the input filter capacitor. Ceramic
bypass capacitors (0.1
μ
F) connected directly to V
CC
, V
C
,
and V
ref
may be required depending upon circuit layout.
This provides a low impedance path for filtering the high
frequency noise. All high current loops should be kept as
short as possible using heavy copper runs to minimize
radiated EMI. The Error Amp compensation circuitry and
the converter output voltage divider should be located close
to the IC and as far as possible from the power switch and
other noise–generating components.
Current mode converters can exhibit subharmonic
oscillations when operating at a duty cycle greater than 50%
with continuous inductor current. This instability is
independent of the regulator’s closed loop characteristics
and is caused by the simultaneous operating conditions of
fixed frequency and peak current detecting. Figure 20A
shows the phenomenon graphically. At t
0
, switch
conduction begins, causing the inductor current to rise at a
slope of m
1
. This slope is a function of the input voltage
divided by the inductance. At t
1
, the Current Sense Input
reaches the threshold established by the control voltage.
This causes the switch to turn off and the current to decay at
a slope of m
2
, until the next oscillator cycle. The unstable
condition can be shown if a perturbation is added to the
control voltage, resulting in a small
I (dashed line). With
a fixed oscillator period, the current decay time is reduced,
and the minimum current at switch turn–on (t
2
) is increased
by
I +
I m
2
/m
1
. The minimum current at the next cycle (t
3
)
decreases to (
I +
I m
2
/m
1
) (m
2
/m
1
). This perturbation is
multiplied by m
2
/m
1
on each succeeding cycle, alternately
increasing and decreasing the inductor current at switch
turn–on. Several oscillator cycles may be required before
the inductor current reaches zero causing the process to
commence again. If m
2
/m
1
is greater than 1, the converter
will be unstable. Figure 20B shows that by adding an
artificial ramp that is synchronized with the PWM clock to
the control voltage, the
I perturbation will decrease to zero
on succeeding cycles. This compensating ramp (m
3
) must
have a slope equal to or slightly greater than m
2
/2 for
stability. With m
2
/2 slope compensation, the average
inductor current follows the control voltage, yielding true
current mode operation. The compensating ramp can be
derived from the oscillator and added to either the Voltage
Feedback or Current Sense inputs (Figure 33).
相關PDF資料 |
PDF描述 |
|---|---|
| UC3842BVDR2 | I2C BUS-CONTROLLED MULTISTANDARD SINGLE CHIP TV PROCESSOR |
| UC3843BD1R2 | 10-line IPAD", EMI filter and ESD protection |
| UC3843BDR2 | 1-bit dual supply bus buffer level translator with A-side series resistor |
| UC3843BVD1R2 | 2-bit dual supply bus transceiver level translator with a side series resistor |
| UC3843BVDR2 | 4-bit dual supply bus buffer level translator with A side series resistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UC3842BVD1R2G | 功能描述:電流型 PWM 控制器 52kHz 1A Current PWM w/96% Duty Cycle Max RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| UC3842BVDR2 | 功能描述:電流型 PWM 控制器 52kHz 1A Current PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| UC3842BVDR2G | 功能描述:電流型 PWM 控制器 52kHz 1A Current PWM w/96% Duty Cycle Max RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| UC3842BVN | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HIGH PERFORMANCE CURRENT MODE CONTROLLERS |
| UC3842CD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。