參數資料
型號： TSS461E-TRDZ-9
廠商： ATMEL CORP
元件分類： 微控制器/微處理器
英文描述： VAN Data Link Controller
中文描述： 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PDSO24
封裝： SO-24
文件頁數： 21/57頁
文件大?。?/td> 817K
代理商： TSS461E-TRDZ-9
21
TSS461E
4194B–AUTO–12/04
If there are less than four edges during one SDC period, the diagnosis mode will
change to the major error mode.
Transmission diagnosis:
The transmission compares RxD1 and RxD2 inputs (through the input comparators
and the filters) with the data transmitted on TxD output.
At a time when the transmission logic generates a dominant (recessive transition),
the inputs can give different values. Taking into account the filtering delay, the bus
line seen as dominant is assumed to be correct, the other one, recessive, is
considered faulty. The diagnosis mode is changed to reflect that.
Protocol fault:
The protocol fault is detected by counting the number of consecutive dominant
timeslots.
If eight consecutive timeslots are dominant, the diagnosis mode will change to the
major error mode.
Generation of Internal
Signals
RI Signal (Return to Idle)
This signal is used to return to nominal mode in the three specified selection modes (see
section “Diagnosis States” and section “Programming Modes”). The RI signal is dis-
abled in automatic selection mode.
The RI signal is a pulse generated when an EOF is detected. So, at the end of each
frame, the user, regarding the diagnosis status bit Sa, Sb & Sc, can select its own
choice.
SDC Signal (Synchronous
Diagnosis Clock)
This time base is used by diagnosis system in automatic selection mode (see
section “Programming Modes”) when no event is recorded on the bus.
The SDC is generated either by a special SDC divider connected to the timeslot clock,
or manually. The SDC clock period must be longer compared to the timeslot duration.
A typical SDC period should be greater than the maximum frame length appearing on
the VAN network.
TIP Signal (Transmission In
Progress)
This signal must be enabled to allow the transmission diagnosis (see section “Transition
Analyses”).
The TIP turns on synchronously at the beginning of the transmission:
For asynchronous bus access, the beginning of SOF,
For synchronous bus access, the beginning of the identifier field,
For a request of in frame reply, the RTR bit of the command field.
The TIP turns off synchronously at the end of the transmission:
after EOF
after a losing of arbitration or a code violation detection
for a requester of in frame reply, when the arbitration is lost on RTR the bit.
This signal is not generated when the transmission logic only sends an ACK.
相關PDF資料
PDF描述
TSS461F VAN Data Link Controller
TSS463-AAR VAN Data Link Controller with Serial Interface
TSS463A-TERZ VAN Data Link Controller with Serial Interface
TSS463C VAN Data Link Controller with Serial Interface
TSS4B02G Single Phase 4.0 Amps. Glass Passivated Super Fast Bridge Rectifiers
相關代理商/技術參數
參數描述
TSS461F 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:VAN Data Link Controller
TSS461F-TDRZ-9 功能描述:網絡控制器與處理器 IC Van Data Link Controller RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
TSS461F-TDSZ-9 功能描述:網絡控制器與處理器 IC ASICS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
TSS463 制造商:Atmel Corporation 功能描述:LAN Node Controller, 16 Pin, SOP 制造商:Temic 功能描述:LAN Node Controller, 16 Pin, SOP
TSS463-AA 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TSS463-AA [Updated 3/03. 60 Pages]
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*