參數資料
型號： TSPC860XRMZPU66D
廠商： Atmel Corp.
英文描述： Integrated Communication Processor
中文描述： 綜合通信處理器
文件頁數： 27/93頁
文件大?。?/td> 1601K
代理商： TSPC860XRMZPU66D
27
TSPC860 [Preliminary]
2129B–HIREL–12/04
MODCK[1-2] must be used to determine the default clocking mode for the TSPC860.
After hardware reset, the MODCK[1-2] pins change function and become outputs. Thus,
if these alternate functions are also desired, then the MODCK[1-2] configuration should
be set with three-state drivers that turn off after HRESET is negated; however, if
MODCK[1-2] pins’ alternate output functions are not used in the system, they can be
configured with pull-up and pull-down resistors.
Signals with open-drain buffers and active pull-up buffers (HRESET, SRESET, TEA, TS,
TA, BI, and BB) must have external pull-up resistors. These signals include the
following:
Some other input signals do not absolutely require a pull-up resistor, as they may be
actively driven by external logic. However, if they are not used externally, or if the exter-
nal logic connected to them is not always actively driving, they may need external pull-
up resistors to hold them negated. These signals include the following:
PORESET
AS
CR/IRQ3
KR/RETRY/IRQ4/SPKROUT (if configured as KR/RETRY or IRQ4)
Any IRQx (if configured as IRQx)
BR (if the TSPC860’s internal bus arbiter is used)
BG (if an external bus arbiter is used)
JTAG and Debug Ports
TCK/DSCK or ALE_B/DSCK/AT1 (depending on the configuration of the DSCK func-
tion) should be connected to ground through a pull-down resistor to disable Debug
Mode as a default. When required, a debug mode controller tool externally drives this
signal high actively to put the TSPC860 into debug mode.
Two pins need special attention, depending on the version of TSPC860 used.
For TSPC860 rev B and later, TDI/DSDI should be pulled up to V
CC
to keep it from
oscillating when unused.
For TSPC860 rev A.3 and earlier, TCK/DSCK should be connected to ground if it is
configured for its DSCK function, as stated above. However, for these versions of
the TSPC860, the pull-down resistor must be strong (for example, 1 k
to overcome
the internal pull-up resistor.
To allow application of any version of processor, perform both of the above actions.
Unused Inputs
In general, pull-up resistors should be used on any unused inputs to keep them from
oscillating. For example, if PCMCIA is not used, the PCMCIA input pins (WAIT_A,
WAIT_B, IP_A[0-8], IP_B[0-8]) should have external pull-up resistors. However, unused
pins of port A, B, C, or D can be configured as outputs, and, if they are configured as
outputs they do not require external terminations.
Unused Outputs
Unused outputs can be left unterminated.
Signal States During
Hardware Reset
During hardware reset (HRESET or PORESET), the signals of the TSPC860 behave as
follows:
The bus signals are high-impedance
The port I/O signals are configured as inputs, and are therefore high-impedance
The memory controller signals are driven to their inactive state
相關PDF資料
PDF描述
TSPC860XRMZQU66D Integrated Communication Processor
TSPC860XRVZPU66D Integrated Communication Processor
TSPC860XRVZQU66D Integrated Communication Processor
TSS10G45S SOLID STATE AC RELAY
TSS10J45S SOLID STATE AC RELAY
相關代理商/技術參數
參數描述
TSPC860XRMZQU66D 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Integrated Communication Processor
TSPC860XRVZPU66D 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Integrated Communication Processor
TSPC860XRVZQU66D 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Integrated Communication Processor
TSPC-DCM600 制造商:Traco Power 功能描述:Bulk
TSPCOS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TREND SERVER PROG MULTI
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*