- 您現在的位置：買賣IC網 > PDF目錄300041 > TPS68000DBTRG4 (TEXAS INSTRUMENTS INC) FLUORESCENT LIGHT CONTROLLER, 100 kHz SWITCHING FREQ-MAX, PDSO30 PDF資料下載
參數資料
| 型號： | TPS68000DBTRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | FLUORESCENT LIGHT CONTROLLER, 100 kHz SWITCHING FREQ-MAX, PDSO30 |
| 封裝： | GREEN, PLASTIC, TSSOP-30 |
| 文件頁數： | 11/25頁 |
| 文件大?。?/td> | 981K |
| 代理商： | TPS68000DBTRG4 |
www.ti.com
r
V +
R
H ) RL
R
L
(11)
r
V +
C
H ) CL
C
H
(12)
Protection
Compensating the Current and Voltage Regulators
Synchronized Burst Dimming
Independent Burst Dimming
C
BF +
4.7
f
D
mF
Hz
(13)
D
B + VBBR
50
%
V
(14)
SLVS524A – OCTOBER 2005 – REVISED FEBRUARY 2006
APPLICATION INFORMATION (continued)
RH is the upper resistor in the divider at the high voltage side, RL is the resistor to GND.
In case of a capacitive divider the ratio can be calculated as shown in Equation 12:
In this case CH is the upper capacitor in the divider at the high voltage side, CL is the capacitor to GND.
The overcurrent protection comparator (OCP) is typically used to monitor output current but can be configured to
monitor any voltage. The comparator uses the internal reference voltage VREF as a fixed threshold. Any voltage
above the internal reference voltage at OCP for more than 4 clock cycles of the main oscillator causes the
comparator to trip and generate a fault. The comparator only will trip with positive voltages above the internal
reference voltage at applied to OCP. Although the input can withstand higher negative voltages there is no
rectification implemented.
The compensation networks for current and voltage regulators are connected between the negative inputs and
the outputs of the respecive amplifier. At the current amplifier the pins are CAM (input) and CAO (output). At the
voltage amplifier VAM (input) and VAO (output) are used. The compensation network must have a dominating
capacitive characteristic, since the error amplifiers are also used for smoothing the half wave rectified feedback
input signal. capacitors in parallel with resistor and capacitor in series or just capacitors are recommended. In
typical applications a 2200 pF capacitor at the current amplifier and a 0.022
F capacitor at the voltage amplifier
can be used.
To configure the device for synchronized burst dimming the dimming PWM signal must be connected directly to
the BC logic input pin. The controller will turn the lamp on and off, following directly the PWM pulses applied at
BC regarding frequency, phase and duty cycle. The slopes of the lamp current are controlled internally. The other
pins used for configuring burst dimming, BBR and BF should have a defined state as well. It is recommended to
connect BBR to 5 V (V5) and to connect BF to GND.
In this configuration the device generates the low dimming frequency and the duty cycle internally. To use this
feature the BC pin should be connected to GND. A capacitor connected to BF is used to program the frequency
of the low frequency oscillator. The capacitance necessary to program a given burst dimming frequency can be
calculated using Equation 13:
CBF is the capacitor required to be connected between BF and GND and fD is the low frequency oscillator
frequency which should be programmed. For example a 0.047
F capacitor is needed to program a burst
frequency of 100 Hz.
To program the burst duty cycle a voltage at BBR is used. The duty cycle can be calculated using Equation 14:
DB is the resulting burst duty cycle and VBBR is the voltage applied at the BBR pin. The operating voltage range
for duty cycle programming is 0 V to 2 V. 0 V at BBR will program 0% burst duty cycle and 2 V will program
100% burst duty cycle.
19
相關PDF資料 |
PDF描述 |
|---|---|
| TPS75101QPWPRQ1 | 1.5 V-5 V ADJUSTABLE POSITIVE LDO REGULATOR, PDSO20 |
| TPS75115QPWPRQ1 | 1.5 V FIXED POSITIVE LDO REGULATOR, PDSO20 |
| TPS75425QPWPREP | 2.5 V FIXED POSITIVE LDO REGULATOR, PDSO20 |
| TPSMC10A/7 | 1500 W, UNIDIRECTIONAL, SILICON, TVS DIODE, DO-214AB |
| TPSMC43A/7 | 1500 W, UNIDIRECTIONAL, SILICON, TVS DIODE, DO-214AB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS68000EVM-161 | 功能描述:電源管理IC開發工具 TPS68000-161 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS68000EVM-166 | 功能描述:電源管理IC開發工具 TPS68000 Evaluation Module RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS68000EVM-202 | 功能描述:電源管理IC開發工具 TPS68000 Evaluation Module RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS68401C3YFFR | 制造商:Texas Instruments 功能描述: |
| TPS68401C4YFFR | 功能描述:LED照明驅動器 Multifunction 3-Ch LED Drvr RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。