- 您現在的位置：買賣IC網 > PDF目錄220050 > TPS65820RSHT (TEXAS INSTRUMENTS INC) 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 PDF資料下載
參數資料
| 型號： | TPS65820RSHT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| 封裝： | 7 X 7 MM, GREEN, PLASTIC, QFN-56 |
| 文件頁數： | 69/98頁 |
| 文件大?。?/td> | 2290K |
| 代理商： | TPS65820RSHT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁當前第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁
GPIO3
INTERNAL ADC
CONVERSIONSTATUS
FIRST
SAMPLE
LAST
SAMPLE
ON
OFF
t
WAIT(TRG)
tDLY(TRG)
CONVERSIONCYCLE
GPIO3
INTERNAL ADC
CONVERSIONSTATUS
FIRST
SAMPLE
LAST
SAMPLE
ON
OFF
TWAIT(TRG)
TDLY(TRG)
CONVERSIONCYCLE
Continuous Conversion Operation (Repeat Mode)
www.ti.com .............................................................................................................................................................. SLVS663B – MAY 2006 – REVISED APRIL 2008
With the default power-up settings (HOLDOFF=LO, ADC_DELAY register), the TPS65820 executes a multiple
sample conversion cycle if the first sample is taken when the trigger is at its active level. Subsequent samples
are converted at the end of the wait time, even if the trigger returns to the non-active level. The external trigger
level edge is ignored until the current conversion cycle ends.
Figure 50. ADC Conversion Triggerd by GPIO3 Positive Edge Triggered Active Level Hi; Holdoff = LC
If the sample conversion needs to be synchronized with an external trigger, during multiple sample conversion
cycles, the control bit HOLDOFF should be set to HI. When the holdoff mode is active, the internal trigger starts
a sample conversion only if the external trigger was detected and is at its active level at the end of the wait time,
as shown in Figure 51.
Figure 51. ADC Conversion Triggerd by GPIO3 Positive Edge-Triggered Active Level HI,
Holdoff = HI, Four Sample Cycles
When the multiple sample cycles are executed the host must configure the maximum and minimum limits for the
ADC output using registers DLOLIM1, DLOLIM2, DHILIM1 and DHILIM2. A conversion cycle ends if any
individual conversion result exceeds the maximum limit value or is below the minimum limit value. When an out
of limit conversion is detected an interrupt is sent to the host, and the ADC_STATUS bit on register ADC
READING_HI is set to DONE.
The TPS65820 ADC can be set to operate in a continuous conversion mode, with back-to-back conversion
cycles executed. The REPEAT mode is targeted at applications where an input is continuously monitored for a
period of time, and the host must be informed if the monitored input is out of the range set by I2C registers
DLOLIM1, DLOLIM2, DHILIM1 and DHILIM2. In REPEAT mode each conversion is started when the ADC trigger
(internal or external) is detected, and a new conversion cycle is started when the current conversion cycle ends.
All the trigger and sampling modes available for normal conversion cycles are available in repeat mode.
Executing I2C read operations to get the ADC readings for average, minimum, maximum and last sample values
is possible in REPEAT mode. However, this is not a recommended operation, as the REPEAT mode does not
generate a DONE status flag making it difficult to synchronize the ADC data reading to the end of a conversion
cycle.
The recommended use of the REPEAT mode is :
1. Configure the ADC conversion cycle : trigger mode, sample mode, select input signal, etc.
2. Configure the HI and LO limits for the ADC readings
3. Set the ADC_DELAY register bit REPEAT to HI
4. Toggle ADC_DELAY register bit ADC_EN bit from LO to HI
Copyright 2006–2008, Texas Instruments Incorporated
71
Product Folder Link(s): TPS65820
相關PDF資料 |
PDF描述 |
|---|---|
| TPS65820RSH | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| TRU050-GACHA-47M4570000 | PHASE LOCKED LOOP, CDSO16 |
| TRU050-GACNA-12M6240000 | PHASE LOCKED LOOP, CDSO16 |
| TRU050-GALNA-20M0000000 | PHASE LOCKED LOOP, CDSO16 |
| TRU050-GALNB-51M8400000 | PHASE LOCKED LOOP, CDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS65820RSHTG4 | 功能描述:電池管理 Int Sgl-Cell Li-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS658310YFFR | 功能描述:PMIC 解決方案 PMU w/Switching Chgr & Lighting Cntrl RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| TPS65835EVM-705 | 功能描述:電源管理IC開發工具 TPS65835 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS65835RKPR | 功能描述:PMIC 解決方案 Adv PMU w/Integrated MSP430 RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
| TPS65835RKPT | 功能描述:PMIC 解決方案 ADVANCED PMU RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。