- 您現在的位置：買賣IC網 > PDF目錄385013 > TPS65013RGZ (Texas Instruments, Inc.) POWER AND BATTERY MANAGEMENT IC FOR Li-ION POWERED SYSTEMS PDF資料下載
參數資料
| 型號： | TPS65013RGZ |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | POWER AND BATTERY MANAGEMENT IC FOR Li-ION POWERED SYSTEMS |
| 中文描述： | 電源和電池管理集成電路鋰離子供電系統 |
| 文件頁數： | 24/52頁 |
| 文件大?。?/td> | 844K |
| 代理商： | TPS65013RGZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
www.ti.com
100% Duty Cycle Low Dropout Operation
VI(min)
VO(max)
IO(max)
rDS(on)max
RL
(2)
Active Discharge When Disabled
Power-Good Monitoring
Overtemperature Shutdown
LOW-DROPOUT VOLTAGE REGULATORS
The low-dropout voltage regulators are designed to operate with low value ceramic input and output capacitors.
They operate with input voltages down to 1.8 V. The LDOs offer a maximum dropout voltage of 300 mV at rated
output current. Each LDO has a current limit feature. Both LDOs are enabled per default; both LDOs can be
disabled or programmed via the serial interface using the VREGS1 register. The LDO outputs (when enabled)
are monitored by power-good comparators, the outputs of which are available via the serial interface. The LDOs
also have reverse conduction prevention when disabled. This allows the possibility to connect external regulators
in parallel in systems with a backup battery.
Power-Good Monitoring
Enable and Sequencing
TPS65013
SLVS517–AUGUST 2004
The TPS65013 converters offer a low input to output voltage difference while maintaining operation with the use
of the 100% duty cycle mode. In this mode, the P-channel switch is constantly turned on. This is particularly
useful in battery-powered applications to achieve longest operation time by taking full advantage of the whole
battery voltage range. The minimum input voltage to maintain regulation depends on the load current and output
voltage and is calculated as:
with:
I
O(max)
= maximum output current plus inductor ripple current
r
DS(on)max
= maximum P-channel switch r
DSon
.
R
L
= dc resistance of the inductor
V
O(max)
= nominal output voltage plus maximum output voltage tolerance
When the CORE and MAIN converters are disabled, due to an UVLO, BATT_COVER or OVERTEMP condition,
it is possible to actively pull down the outputs. This feature is disabled per default and is individually enabled via
the VDCDC1 and VDCDC2 registers in the serial interface. When this feature is enabled, the core and main
outputs are discharged by a 400-
(typical) load.
Both the MAIN and CORE converters have power-good comparators. Each comparator indicates when the
relevant output voltage has dropped 10% below its target value, with 5% hysteresis. The outputs of these
comparators are available in the REGSTATUS register via the serial interface. A maskable interrupt is generated
when any voltage rail drops below the 10% threshold. The comparators are disabled when the converters are
disabled. The status of the power-good comparator for VMAIN is used to generate the RESPWRON signal.
The MAIN and CORE converters are automatically shut down if the temperature exceeds the trip point (see the
electrical characteristics). This detection is only active if the converters are in PWM mode, either by setting
FPWM = 1, or if the output current is high enough that the device runs in PWM mode automatically.
Both the LDO1 and LDO2 linear regulators have power-good comparators. Each comparator indicates when the
relevant output voltage has dropped 10% below its target value, with 5% hysteresis. The outputs of these
comparators are available in the REGSTATUS register via the serial interface. An interrupt is generated when
any voltage rail drops below the 10% threshold. The LDO2 comparator is disabled when LDO2 is disabled.
Enabling and sequencing of the dc-dc converters and LDOs are described in the power-up sequencing section.
The OMAP1710 processor from Texas Instruments requires that the core power supply is enabled before the I/O
power supply, which means that the CORE converter should power up before the MAIN converter. This is
achieved by connecting PS_SEQ to GND.
24
相關PDF資料 |
PDF描述 |
|---|---|
| TPS65020RHA | POWER MANAGEMENT IC FOR LI-ION POWERED SYSTEMS |
| TPS65100RGE | TRIPLE OUTPUT LCD SUPPLY WITH LINEAR REGULATOR AND VCOM BUFFER |
| TPS65105RGE | TRIPLE OUTPUT LCD SUPPLY WITH LINEAR REGULATOR AND VCOM BUFFER |
| TPS65111 | Triple Chargepump for LTPS LCD |
| TPS65110RGE | LTPS LCD BIAS POWER SUPPLY TRIPLE CHARGE PUMP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS65013RGZR | 功能描述:電池管理 Multi-Channel 1-cell Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65013RGZRG4 | 功能描述:電池管理 Multi-Channel 1-cell Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65013RGZT | 功能描述:電池管理 Multi-Channel 1-cell Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65013RGZT | 制造商:Texas Instruments 功能描述:IC POWER/BATTERY MGMT 48-QFN 制造商:Texas Instruments 功能描述:IC, POWER/BATTERY MGMT 48-QFN 制造商:Texas Instruments 功能描述:IC, POWER/BATTERY MGMT 48-QFN; Battery Type:Li-Ion, Li-Polymer; No. of Pins:48; No. of Series Cells:1; Operating Temperature Min:-40C; Operating Temperature Max:85C; MSL:MSL 2 - 1 year; SVHC:No SVHC (19-Dec-2012); Base ;RoHS Compliant: Yes |
| TPS65013RGZTG4 | 功能描述:電池管理 Multi-Channel 1-cell Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。