參數資料
型號: TPS24711DGSR
廠商: Texas Instruments
文件頁數: 25/34頁
文件大?。?/td> 2792K
描述: IC CTRLR HOT SWAP 2.5-18V 10MSOP
標準包裝: 1
類型: 熱交換控制器
應用: 通用
內部開關: 無
電流限制: 可調
電源電壓: 2.5 V ~ 18 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 10-TFSOP,10-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 10-MSOP
包裝: 標準包裝
其它名稱: 296-28562-6
OUT
VCC
C
V
t
I
?/DIV>
=
2
ENTHRESH
VCC
R
V
R   R
=
?/DIV>
+
G009
1k
10
0.01
1
100
0.1
0.01
0.1
10
100
1
Single Pulse
R    = 94篊/W (min Cu)
窲A
1ms
10ms
100ms
1s
DC
Area Limited
by R
DS(on)
V    Drain-to-Source Voltage  V
DS
TPS24710,TPS24711
TPS24712,TPS24713
www.ti.com
SLVSAL2E JANUARY 2011REVISED NOVEMBER 2013
Figure 35. CSD16403Q5 SOA Curve
STEP 5. Calculate the Retry-Mode Duty Ratio
In retry mode, the TPS24711/13 is on for one charging cycle and off for 16 charge/discharge cycles, as can be
seen in Figure 32. The first C
T
charging cycle is from 0 V to 1.35 V, which gives 7.56 ms. The first C
T
discharging
cycle is from 1.35 V to 0.35 V, which gives 5.6 ms. Therefore, the total time is 7.56 ms + 33 ?5.6 ms = 192.36
ms. As a result, the retry mode duty ratio is 7.56 ms/192.36 ms = 3.93%.
STEP 6. Select R
1
and R
2
for UV
Next, select the values of the UV resistors, R
1
and R
2
, as shown in the typical application diagram on the front
page. From the TPS24710/11/12/13 electrical specifications, V
ENTHRESH
= 1.35 V. The V
UV
is the undervoltage
trip voltage, which for this example equals 10.7 V.
(13)
Assume R
1
is 130 k& and use Equation 13 to solve for the R
2
value of 18.7 k&.
STEP 7. Choose R
GATE
, R
4
, R
5
and C
1
In the typical application diagram on the front page, the gate resistor, R
GATE
, is intended to suppress high-
frequency oscillations. A resistor of 10 ?will serve for most applications, but if M
1
has a C
ISS
below 200 pF, then
33 ?is recommended. Applications with larger MOSFETs and very short wiring may not require R
GATE
. R
4
and
R
5
are required only if PGb and FLTb are used; these resistors serve as pullups for the open-drain output
drivers.  The  current  sunk  by  each  of  these  pins  should  not  exceed  2  mA  (see  the  RECOMMENDED
OPERATING CONDITIONS table). C
1
is a bypass capacitor to help control transient voltages, unit emissions,
and local supply noise while in the disabled state. Where acceptable, a value in the range of 0.001 糉 to 0.1 糉
is recommended.
ALTERNATIVE DESIGN EXAMPLE: GATE CAPACITOR (dV/dt) CONTROL IN INRUSH MODE
The TPS24710/11/12/13 can be used in applications that expect a constant inrush current. This current is
controlled by a capacitor connected from the GATE terminal to GND. A resistor of 1 k& placed in series with this
capacitor will prevent it from slowing a fast-turnoff event. In this mode of operation, M
1
operates as a source
follower, and the slew rate of the output voltage approximately equals the slew rate of the gate voltage (see
Figure 36).
To implement a constant-inrush-current circuit, choose the time to charge, t, using Equation 14,
(14)
where C
OUT
is the output capacitance, V
VCC
is the input voltage, and I
CHG
is the desired charge current. Choose
I
CHG
< P
LIM
/ V
VCC
to prevent power limiting from affecting the desired current.
Copyright ?20112013, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Links: TPS24710  TPS24711 TPS24712  TPS24713
相關PDF資料
PDF描述
TPS2491DGSG4 IC POS HV HOT-SWAP CTRLR 10-MSOP
W83772G IC H/W MONITOR 8-TSSOP
W83L786G IC H/W MONITOR 28-SSOP
X96011V14IZ IC SENSOR TEMP BIAS SGL 14-TSSOP
XR4151CP-F IC CONV VF/FV 8PDIP
相關代理商/技術參數
參數描述
TPS24711EVM-004 功能描述:電源管理IC開發工具 TPS24711 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS24712DGS 功能描述:熱插拔功率分布 2.5-18V Hi Eff Pwr- Ltd Hot-Swap Cntrlr RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS24712DGSR 功能描述:熱插拔功率分布 2.5-18V Hi Eff Pwr- Ltd Hot-Swap Cntrlr RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS24713DGS 功能描述:熱插拔功率分布 2.5-18V Hi Eff Hot- Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS24713DGSR 功能描述:熱插拔功率分布 2.5-18V Hi Eff Hot- Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube