- 您現在的位置：買賣IC網 > PDF目錄385931 > TLK2201AIRCPR (Texas Instruments, Inc.) ETHERNET TRANSCEIVERS PDF資料下載
參數資料
| 型號： | TLK2201AIRCPR |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | ETHERNET TRANSCEIVERS |
| 中文描述： | 以太網收發器 |
| 文件頁數： | 17/21頁 |
| 文件大小： | 343K |
| 代理商： | TLK2201AIRCPR |
TLK2201A, TLK2201AI
ETHERNET TRANSCEIVERS
SLLS572
–
JUNE 2003
17
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
designing with PowerPAD
(continued)
It is recommended that there be a thermal land, which is an area of solder-tinned-copper, underneath the
PowerPAD package. The thermal land varies in size depending on the PowerPAD package being used, the PCB
construction, and the amount of heat that needs to be removed. In addition, the thermal land may or may not
contain numerous thermal vias depending on PCB construction.
Other requirements for thermal lands and thermal vias are detailed in the TI application note
PowerPAD
Thermally Enhanced Package Application Report
, TI literature number SLMA002, available via the TI Web
pages beginning at URL:
http://www.ti.com.
Figure 13. Example of a Thermal Land
For the TLK2201A, this thermal land must be grounded to the low-impedance ground plane of the device. This
improves not only thermal performance but also the electrical grounding of the device. It is also recommended
that the device ground pin landing pads be connected directly to the grounded thermal land. The land size must
be as large as possible without shorting device signal pins. The thermal land may be soldered to the exposed
PowerPAD using standard reflow soldering techniques.
While the thermal land may be electrically floated and configured to remove heat to an external heat sink,
it is
recommended
that the thermal land be connected to the low-impedance ground plane for the device. More
information may be obtained from the TI application note
PHY Layout
, TI literature number SLLA020.
相關PDF資料 |
PDF描述 |
|---|---|
| TLN103A | INFRARED LED FOR PHOTOSENSORS |
| TLN115A | LED GAAS |
| TLOE156P | InGaAlP Orange Light Emission(InGaAlP橙色發光燈（LED照明燈）) |
| TLOH156P | Panel Circuit Indicator(平板電路指示器（橙色LED）) |
| TLOH157P | Panel Circuit Indicator(平板電路指示器（橙色LED）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLK2201AIRCPRG4 | 功能描述:以太網 IC 1.0 to 1.6 Gbps Gb Ethernet Transceiver RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| TLK2201AJR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.0Gb to 1.6Gb SMALL FORM-FACTOR ETHERNET TRANSCEIVER |
| TLK2201AJRGQE | 功能描述:以太網 IC 1.0 to 1.6 Gbps Ethernet Trnscvr RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| TLK2201AJRZQE | 功能描述:以太網 IC 1.0-1.6 Gbps Gigabit Ethernet Trncvr RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| TLK2201ARCP | 功能描述:以太網 IC 1.0 to 1.6 Gbps Gb Ethernet Transceiver RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。