- 您現在的位置：買賣IC網 > PDF目錄69493 > TLC320AD50CPTR (TEXAS INSTRUMENTS INC) SPECIALTY ANALOG CIRCUIT, PQFP48 PDF資料下載
參數資料
| 型號： | TLC320AD50CPTR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP48 |
| 封裝： | PLASTIC, QFP-48 |
| 文件頁數： | 22/56頁 |
| 文件大小： | 555K |
| 代理商： | TLC320AD50CPTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
3–2
3.2
Secondary Serial Communication
Secondary serial communication is used to read or write 16-bit words that program both the options and the circuit
configurations of the device. Register programming always occurs during secondary communication. Four primary
and secondary communication cycles are required to program the four registers. If the default value for a particular
register is desired, then the register addressing can be omitted during secondary communications. The NOOP
command addresses a pseudoregister, register 0, and no register programming takes place during this secondary
communication. If secondary communication is desired for any device (either master or slave), then a secondary
communication must be requested for all devices, starting with the master. This results in a secondary frame sync
(FS) for all devices. The NOOP command can be used for devices that do not need a secondary operation.
During secondary communication, a register may be written to or read from. When writing a value to a register, DIN
contains the value to be written. When reading the value in a register, the data is stepped out on DOUT.
There are two methods for initiating secondary communications:
1.
By asserting a high level on FC
2.
By asserting the LSB of the DIN 16-bit serial communication high while in the15-bit mode
Both methods are illustrated in Figure 3–2.
Secondary
Request
16-Bit Mode
(Control 1 Register, Bit 0)
FC
(Hardware)
(LSB of DIN)
Internal TLC320AD50C
Figure 3–2. Hardware and Software Methods to Make a Secondary Request
FC should be pulled high before the rising edge of the frame sync (FS). This causes the start of the secondary
communication, 128 SCLKs after the start of the primary communication frame. If slaves are present, FC should
remain high until the rising edge of the frame sync for the last slave.
The second method for secondary communication is by asserting the LSB high. The least significant bit (D0) can be
used for the secondary requests as shown in Table 3–1. The request is made by placing the device in the 15-bit DAC
mode and making the LSB of DIN equal to 1. All devices should be in the 15-bit DAC mode and secondary
communication should be requested for all devices.
Table 3–1. Least Significant Bit Control Function
CONTROL BIT D0
CONTROL BIT FUNCTION
0
No operation (NOOP)
1
Secondary communication request
If a secondary communication request is made, FS goes low after 128 SCLKs after the beginning of the primary frame.
相關PDF資料 |
PDF描述 |
|---|---|
| TLC320AD50IPTR | SPECIALTY ANALOG CIRCUIT, PQFP48 |
| TLC320AD50IPT | SPECIALTY ANALOG CIRCUIT, PQFP48 |
| TLC555QDRQ1 | PULSE; RECTANGULAR, 1.2 MHz, TIMER, PDSO8 |
| TLC7701MPWREPG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TLC7705QPWREP | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC320AD50I | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SIGMA-DELTA ANALOG INTERFACE CIRCUITS WITH MASTER-SLAVE FUNCTION |
| TLC320AD50IDW | 功能描述:接口—CODEC SNGL CH Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| TLC320AD50IPT | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SIGMA-DELTA ANALOG INTERFACE CIRCUITS WITH MASTER-SLAVE FUNCTION |
| TLC320AD52CDW | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SIGMA-DELTA ANALOG INTERFACE CIRCUITS WITH MASTER-SLAVE FUNCTION |
| TLC320AD52CPT | 功能描述:IC ANALOG INTERFACE W/MS 48-LQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:- 標準包裝:2,500 系列:- 類型:PCM 數據接口:PCM 音頻接口 分辨率（位）:15 b ADC / DAC 數量:1 / 1 三角積分調變:是 S/N 比，標準 ADC / DAC (db):- 動態(tài)范圍，標準 ADC / DAC (db):- 電壓 - 電源，模擬:2.7 V ~ 3.3 V 電壓 - 電源，數字:2.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-VFBGA 供應商設備封裝:80-BGA MICROSTAR JUNIOR（5x5） 包裝:帶卷 (TR) 其它名稱:296-21257-2 |
發(fā)布緊急采購，3分鐘左右您將得到回復。