- 您現在的位置：買賣IC網 > PDF目錄196421 > TFDS6502E-TR3 (VISHAY SEMICONDUCTORS) SPECIALTY INTERFACE CIRCUIT, XMA8 PDF資料下載
參數資料
| 型號： | TFDS6502E-TR3 |
| 廠商： | VISHAY SEMICONDUCTORS |
| 元件分類： | 其它接口 |
| 英文描述： | SPECIALTY INTERFACE CIRCUIT, XMA8 |
| 封裝： | 13 X 5.95 X 5.30 MM, SIDE VIEW-8 |
| 文件頁數： | 17/18頁 |
| 文件大小： | 690K |
| 代理商： | TFDS6502E-TR3 |
TFDU6102E/TFDS6402/TFDS6502E/TFDT6502E
Vishay Semiconductor
Rev. B1.6, 02–Nov–00
8
www.vishay.com
Document Number 82526
Recommended Circuit Diagram
The only required component for designing an
IrDA 1.3
solution
using
Vishay
Telefunken
transceivers is a current limiting resistor, R1, to the
IRED. However, depending on the entire system
design and board layout, additional components may
be required (see figure 3).
IRED
Cathode
IRED
Anode
Rxd
Vcc
GND
Txd
SD/Mode
Mode
TFDx6x0xE
C2
C1
R2
R1
VCC2
Rxd
GND
VCC1
SD/Mode
Txd
Note: outlined components are optional depending
on the quality of the power supply
Figure 3. Recommended Application Circuit
Vishay Telefunken transceivers integrate a sensitive
receiver and a built-in power driver. The combination
of both needs a careful circuit board layout. The use of
thin, long, resistive and inductive wiring should be
avoided. The inputs (Txd, SD/ Mode) and the output
Rxd should be directly (DC) coupled to the I/O circuit.
R1 is used for controlling the current through the
IR emitter. For increasing the output power of the
IRED, the value of the resistor should be reduced.
Similarly, to reduce the output power of the IRED, the
value of the resistor should be increased. For typical
values of R1 see figure 4. For IrDA compliant
operation, a current control resistor of 7.2
is
recommended. For compensating losses of the cos-
metic window, reducing that value to 5.6
is
acceptable. The upper drive current limitation is
dependent on the duty cycle and is given by the
absolute maximum ratings on the data sheet.
R2, C1 and C2 are optional and dependent on the
quality of the supply voltage VCC and injected noise.
An unstable power supply with dropping voltage during
transmission may reduce sensitivity (and transmission
range) of the transceiver.
The placement of these parts is critical. It is strongly
recommended to position C2 as near as possible to the
transceiver
power
supply
pins.
An
electrolytic
capacitor should be used for C1 while a ceramic
capacitor is used for C2.
Table 1. Recommended Application Circuit Components
Component
Recommended Value
Vishay Part Number
C1
4.7
mF, Tantalum
293D 475X9 016B 2T
C2
0.1
F, Ceramic
VJ 1206 Y 104 J XXMT
R1
5 V supply voltage: 7.2
, 0.25 W
(recommend using
two 3.6
W, 0.125 W resistors in series)
3.3 V supply voltage: 3.6
, 0.25 W
(recommend using
two 1.8
W, 0.125 W resistors in series)
CRCW–1206–3R60–F–RT1
CRCW–1206–1R80–F–RT1
R2
47
, 0.125 W
CRCW–1206–47R0–F–RT1
相關PDF資料 |
PDF描述 |
|---|---|
| TFDT6502E-TR3 | SPECIALTY INTERFACE CIRCUIT, XMA8 |
| TFECH8SA254AY | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 9.4mm, PANEL MOUNT |
| TFCDF5VA154AC | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 1A, 30VDC, 4.19mm, PANEL MOUNT |
| TFCDF5VT135AW | SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 1A, 30VDC, 4.19mm, PANEL MOUNT |
| TFCDH8SA105BC | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 2.28mm, PANEL MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TFDT4000 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:Integrated Transceiver |
| TFDT4500 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:2.7-5.5V Serial Infrared Transceiver Module Family |
| TFDT6000-TR3 | 制造商:TEMIC 功能描述: |
| TFDT6500E | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:2.7-5.5V Fast Infrared Transceiver Module Family |
| TFDT6501E | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Fast Infrared Transceiver Module Family (FIR, 4 Mbit/s) for 2.6 V to 5.5 V Operation |
發布緊急采購，3分鐘左右您將得到回復。